DP940PWSQ0 Whirlpool Dishwasher - Instructions

removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine.

Disconnect power supply to dishwasher. Open door and remove screws on inner door cover. Carefully remove inner cover while watching how inner parts are arranged. Found return spring on detergent cup linkage had rusted and broken causing detergent cup not to open. Installed new spring and re assembled inner cover. Rotated timer dial one full revolution to check operation of detergent cup. Worked like a charm. Re connect power supply to dishwasher and your good to go.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Diagnosing the problem, i.e. finding the source of the leak, was the hardest part. The best clue was the leak only occurred well into the cycle when the water was hot and steam was coming out the vent. I then assumed there was a bad seal and steam & condensed water was leaking down into the door. I replaced the vent duct & seal, a broken drip cover (an internal part in the door), and replaced a missing rinse aid cap. This stopped the leak.

I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassembled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!

I just changed all parts that could make any effect in temperature control. even the thermal fuse. this was easy,looking in details all the drawings you have in your page. so I pulled out the dishwasher changed the parts and ready!! it work great now . thanks for your guide and help.

Water was not being sprayed thru the arms. I opened the dishwasher, removed/unscrewed the spray arms and wash impeller (black plastic wheel that directs the water) and then noticed that the part below the wash impeller had broken into pieces. There was only a metal ring and it was supposed to have a spring attached to it. I replaced the ring/spring below the wash impeller using the part from the Drain and Wash impeller kit. The dishwasher works great now.

It was my first mechanical fix. Use the web to diagnose, find the specs of the appliance and use common sense and you can do it yourself too.

By the way, the parts from this site arrived the next day.

After hearing ominous grinding sounds and water leaking around the gasket, it was about time to rehab the dishwasher. This is usually the point where I say "t'hell with it, buy a new one". I am glad I didn't.
The Kit to rehab the impeller and such had EVERYTHING I needed. Right parts, right price.
Removed the upper arm assembly, T15 screwdriver, the screen strainer, the impeller, T25 screwdriver, the food grinding spring and impeller (the grinding noise, spring was sprung), and finally the post and impeller thingie (had to break it off, very brittle). The pieces went back on a lot more smoothly than it took to get them off!
Use your digital camera! I took pictures of every stage of the parts removal and what I removed. I got confused with some little balls that were inside and the pictures told me exactly where they went.
Door gasket? I should have replaced it YEARS ago, so easy and cheap with PartSelect parts.

I removed all the ( what my Husband called star screws ) star screws and removed the housing panel ( holds dish detergent cup and silverware basket ) I discovered everything accross the bottom was all gucked up with detergent soap accumulation. I took the part to the kitchen sink and used the sprayer hose on the part with hot water and it cleaned up beautifully, and the detergent latch then worked ( the spring that operates the latch was all gucked up with detergent accumulation ).
I am the wife and did all of this myself and it only took around 5-10 min. My Husband had to help me figure out the type of screws because they turned out to not be phillip screws, but as Hubby called them.."star screws".
Soooo, I did not need to use the Latch Kit I purchased, so will store it in my parts supply! :)
Happy repairs to you..
Judy Estes Park, CO

replaced the two water defiector's, I had changed the door seal and should have changed the defiectors at the same time. Save yourself some time and ordor both parts. This is a easy fix, anyone can do.

Was able to replace and repair without taking the dishwasher out. Thermostat is behind and to the left of the power junction box. Has 2 wires going to it. It is up against the bottom of tub. I used an angled mirror to see what I was doing. 1 small screw to detach and pull down thermostat. Be sure power is off before you start. Also reprogrammed defaults. Hit any button 1-2-3, 1-2-3, 1-2-3, fast and close door. Let it sit 15 min to run and re-set defaults. Now I have heat and dry dishes.

I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards

Removed 5 or 6 screws replaced O ring,Srewed cover back on ,no more leak.

Replaced the hose assembly on a Kenmore portable dishwasher/

Removed dishwasher, take to garage, removed lower rack to gain access to top of motor unit. Used star socket wrench to remove upper screws holding top of unit in. Disconnect wires, drain tube and counter weight. pulled motor unit out from inside dishwasher and placed on bench. Proceeded to disassemble motor. Some things were obvious, others not so. replaced old worn out parts with new, used a little lube (Vaseline) in places to assist in getting seals back in place. Instructions were of little help need to pay close attention when tearing unit apart. Reassembled with new seals, installed motor and re-installed dishwasher...NO LEAKS!! Wife and I happy.