DP8700XTN5 Whirlpool Dishwasher - Instructions

As there was not a replacement gasket listed in the parts lists or schematics, I ordered the entire nozzle cap hoping the gasket would come with it. It didn't so I glued the gasket in place and installed the new cap. I also replaced the washer arm bearing while I had the cap off. I am hoping the nozzle stays in place.

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.

followed the basic instructions / diagram supplied, however the impeller was fused to the shaft. Used high speed cutter to remove old impeller and sandpaper to clean up shaft.

I tried going online to get some diagnostic help and never found a site that had a step by step help plan. I then did a little reading on different sites, to eliminate and perhaps diagnose my problem I use epoxy to glue the impeller(which spun freely) to the screw and it held long enough for me to see how it worked. I surfed sites to find the least expensive drain and wash impeller kit. One site had a cheaper price but I chose Parts Select because of the shipping so the end result was the best results for me. I am not sure but the estimated time was 1.7 or 1.8 days delivery that I did not believe would happen. When I received the parts and did the repair my final time from ordering was less than a day and a half. I could not have done the job myself without the video because the parts were very different. My biggest obstacle, other than my ignorance, was some sort of chemical on the screw that would not allow me to loosen it. I used a dremel to cut the head off and then a torch to heat the stub so I could remove it. After I received the kit I saw a chemical on the screw threads so online research told me heat loosens the chemical. My dishwasher is around 25 years old,I have worked on it three times now and replacing the impeller was the most difficult task to date. Should it last and develop another problem I will go to parts select first and start my quest.

Dishwasher Stopped then only made a humming noise. Started with the Video on your site and it was quite helpful. I had trouble holding the drain impeller with the wrench. Used a drill to bore holes around the center and then broke the outer ring off to get a good hold on the center. Then was able to remove the bolt. The rest of the repair was easy. Something had caught the chopper blade and unraveled the spring. Replaced all the parts and it is working fine now.

I could not find a 90 degrees 1 inch car wrench and by them the impeller head wish is plastic was all run down so nothing will hold it, finally, I heat up a flat screw driver and cut the impeller near the head whit the help of a hammer , and them I could grab it with a pressure wrench and loose the screw up. finally the fix when fine and is working good. the parts are just the ones I need it. Thank you.

I ordered door cover kit #4387043. It comes with new door cover (lid), new pin, spring, latch and snap. Two problems I encountered was 1)with the spring - there is a trick to replacing it. I had to look up how to put the spring on properly. Go to YouTube and Partselect "Dishwasher Repair - Replacing the Lid Spring (Whirlpool Part # 8066018) " will show you the trick. Was a cinch after I knew the trick. 2) you must take door apart to replace snap that goes with the latch, so you might want to replace the detergent door first and see if that solves your problem without changing the latch. It is workable, but I had to go on line and look for diagram to put back together. Just frustrating but for less than $20.00 solved the problem. Good luck.

Watched your video

Turned off electric to machine.Removed water with shop vac, Removed lower panel, removed drain hose from check valve and garbage disposal. using shop vac removed blockage from drain hose. Reconnected hose turned on electric cycled dishwasher. Didn't work. Turned off electric, removed water, removed basket, sprayer arm, pump cover, used a six point deep socket to hold impeller while removing 1/4 in. screw. Removed the impeller and found the problem.The lower impeller shaft is broke. removed separator, chopper blade and spring, removed pump cover and broken drain impeller and lower seal. Cleaned all old parts and installed new drain pump kit. Replaced spray arm , basket . Turned electric on, cycled the machine one time. Checked for leaks, replaced lower panels. Put away tools. Your video was very helpful. Your service was great. I received the parts the next day after ordering them. thank you. thank you.

We followed the excellent video until we couldn't remove the outlet impeller because the motor shaft was not being held by the failed impeller. We drilled small holes around the impeller shaft until we could break off the upper part of the pump shell. Then we could hold the motor shaft with a vice-grip pliers by squeezing the shaft of the remaing impeller piece. We then removed the retaining screw and the rest of the impeller. Then evrything went well by following the video. There was still a bit of doubt because we discarded more old parts then expected but the machine now works well and we see no leaks.

The video was great! I couldn't have done it without it. The repair took me a little longer than expected because I did not have the right tools (torx head screwdriver), but once I went out and bought it, the rest was fairly easy. The old impeller had some build-up on it, so it was pretty hard taking it off the motor shaft: this was one of the hardest parts, since I was afraid of forcing it out and breaking something. Once I cleaned up the motor shaft, however, the new impeller went in easily. Both the old impeller and washer seal were damaged. Overall, I was very happy with Partselect's fast shipping, easy-to-use website and incredibly helpful installation videos. The machine is now not only NOT leaking anymore, but dishes are coming out MUCH cleaner. The dishwasher is over ten years old, so I was happy that this low-cost fix made such a big difference and we didn't have to buy a whole new dishwasher.

The dishwasher was making grinding noises and then stopped draining at all. I was able to follow the video directions and replace the parts from the drain and wash impeller kit, but it did not solve the problem. Must be the pump or something else. Was worth a try and partselect.com was good with service and price.

Heard a grinding noise in our dishwasher one night recently while it was in the drain mode. Water wasn't draining out so I had to siphon it out with a tube, cup, and rags, then looked up information about the washer/dryer on the internet and found PartsSelect. I watched the repair video they provided and decided to give the repair a try. I began to remove all the necessary parts following the instructional video.
The hardest part of the job came early on, and once that was completed the rest of the job was a cinch. The center screw holding the upper impeller was the hardest part to remove. I tried to use the adjustable wrench on the hex shaped nut molded to the impeller while turning the screw, but that old screw was so tight I was afraid I'd strip the molded impeller nut.
I then tried a 1 inch nut without the driver attached to it but with a pair of vice grips clamped at about 45 degree angle on the 1 inch nut and set on the molded impeller nut while at the same time trying to remove the screw by putting the small nut driver through the top of the 1 inch nut and turning it. No luck there either. It would not budge.
By this time I was entertaining the idea of buying a new 5 to 800.00 dishwasher.
Well I had nothing else to lose except 5 to $800.00, so I reverted to caveman technology.
I ended up using a small chisel and wood mallet to get the impeller off the shaft. Since the impeller is made of a rubber like material, it came off easily in pieces using some careful strikes with the hammer on the impellers molded nut. When this was complete, I unscrewed and removed the filter housing.
The impeller screw, which was still in the motor shaft, and was removed 'after' this because there was no impeller or filter chamber in the way. There was a small space between the screw and the motor shaft since the impeller was removed from around that screw so I first tightened it a little bit, then finally was able to loosen the screw. You would think that screw had been super glued into that shaft but it finally came out. After that I removed the chopper blade and found that the spring attached to it was bent and had tore the shaft of the 'lower' drain impeller to pieces. After cleaning up the impeller pieces I ordered the drain and wash impeller kit from PartSellect. It arrived in a couple of days and the new parts installation went quickly.I was especiially relieved that the new screw and impeller went on without a hitch.
I didn't use the new shaft seal provided because it was a different height then the original seal and wouldn't allow the cover to the drain impeller to seat properly. The height of the new seal also caused the new drain impeller to push or spring up too high.The original seal looked fine so I used that and it worked just fine also. Started the dishwasher up for a test and it all worked flawlessly. No noise no leaks. This was my first washer dryer repair. Following the Part Sellect instructional video with Steve explaining while doing the removal of old and installation of the new parts was a breeze. SO, here's my conclusion. Folks, for under $50.00 I saved a lot of money and expect that I'll get at least a few years more use from this old dishwasher. Thanks again to PartSelect and Steve for your help.

My model was DU7600XS0. I disassembled according to the video and the parts diagram here. I found a piece of metal, a pebble, and a wrecked drain impeller. I cleaned out all the debris and began reassembly. I found that the chopper blade shipped with this kit has a lip and will not fit over the metal drain impeller sleeve on this model. It needs to, or else it will not screw together properly and the impeller will not be able to turn. My old one was undamaged, so I used that instead. Also, the large black wash impeller has a shaft that is longer than the original part and because of that, it would not screw on. Again, the original wash impeller was fine, so I used the old one. I replace the gaskets and screwed everything else back together. It works great now. No water is left after the cycle anymore and the sound it makes is back to normal. Money well spent on this kit!