DP8500XTN2 Whirlpool Dishwasher - Instructions

Unscrewed the old one and replaced it with the new one. My wife actually ordered this Pat and repaired the dishwasher.

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

Put on new door, making sure the spring was set to flip the detergent door open in order for the detergent to properly do the dishes

Turn off the breaker to the dishwasher - there will be water very near the motor and other electrical components. I first scooped and towelled all the water out of the bottom of the dishwasher. The drain valve can be accessed from the bottom front of the dishwasher without pulling the unit out from under the counter. There were 4 screws to remove the 2 bottom metal panels. Next use pliers to loosen and slide back the hose clamp connected to the drain. Have a towel ready and pull the drain hose off the white check valve. The check valve can then be removed by unscrewing it - you may need to use pliers. Put the new one on and everything back together.

Removed cover and broken spring ,installed new spring and cover.Did it all in less than 10 minutes

popped off the old rollers + tracks; then snapped on the new ones; as my granddaughter would say "easy peasy lemon squeezy". Took hardly any time at all. :-)

I used a screwdriver to snap off the old wheel carriers. When Ito attached the new pieces the tray wouldn't close. It was too wide. The person at Part Select was most helpful and patient but I still couldn't get them attached so the tray would fit. Then this week-end I visited my daughter and looked in her dishwasher, not the same brand but I could see how they attached, came home tonight and was able to figure it our easily. May I say a visual would have helped but your sales person was excellent.

My soap dispenser latch was coated in grit, the gasket was deteriorated, and the spring was barely strong enough to open the door, so the door didn't always latch closed or open when it should. I followed the video and everything went exactly as shown. Once the liner was removed, I discovered the back (including the latch mechanism) was covered in soap residue and other gunk. I hosed it off on the backyard and resumed the repair. The dispenser now latches easily and opens with a convincing SNAP. I wouldn't have known how to replace the latch without the video. Great website!

I ordered the parts on Fri. and they came on Sat. Thanks. I had to pull the dishwasher forward about 6". Then just put the springs on. They don't have much tension with the door closed. Easy. Thanks again.

I ordered door cover kit #4387043. It comes with new door cover (lid), new pin, spring, latch and snap. Two problems I encountered was 1)with the spring - there is a trick to replacing it. I had to look up how to put the spring on properly. Go to YouTube and Partselect "Dishwasher Repair - Replacing the Lid Spring (Whirlpool Part # 8066018) " will show you the trick. Was a cinch after I knew the trick. 2) you must take door apart to replace snap that goes with the latch, so you might want to replace the detergent door first and see if that solves your problem without changing the latch. It is workable, but I had to go on line and look for diagram to put back together. Just frustrating but for less than $20.00 solved the problem. Good luck.

As there was not a replacement gasket listed in the parts lists or schematics, I ordered the entire nozzle cap hoping the gasket would come with it. It didn't so I glued the gasket in place and installed the new cap. I also replaced the washer arm bearing while I had the cap off. I am hoping the nozzle stays in place.

Replacing the cup latch and dispenser cover was pretty easy. First, I removed the inside cover of the door of the dishwasher. Then I carefully removed the plastic covers/slides on the door, removed the broken cup latch and then inserted the new one. Replaced the plastic covers/slides, the reinstalled the inside cover on the dishwasher. Next, I removed the dispenser cover and installed the new one. It snaps off/on, by the way. It only looks like it slides on/off.

I installed the opener spring in the direction it was needed to open the door then installed the pin. I placed the door in the position it goes and took a pair of pliers and squeezed the pin into the pin slot. the spring has to be forced into a tension position. I did this by sliding the spring to one side and forcing it into position, the other side is done the same way. works great

I simply looked at the remaining spring to see which notch it needed to be attached to. I went in very well using a long needle nose plier. Works great.

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install