DP840DWGX2 Whirlpool Dishwasher - Instructions

1-2-3 EASIEST JOB I EVER HAD to DO AND THE WIFE IS PROUD OF ME FINALLY.

THANKS , , ,Bat from WEST SENECA (Buffalo, NY)

I Disconected The 3' hose Behind Impellor.Unscrew Cap Holding Impellor In. Pull It Out, Replce With New One.Put It Back Together In Reverse

I went on line and found the partselect website and was able to identify the defective parts using the schematic drawings. I ordered the parts and in about an hour I had reassembled the dishwasher and had it running again much to the joy of my wife and children. (No more washing dishes by hand!). I also purchased the touch-up paint and tine tips and now the washer looks and runs like it did when I purchased it.

This was an easy fix. My husband took out the old gasket and put the new one in. It fit perfectly and no more leak. The part got to us really quickly too and that was nice. No more hand washing the dishes! :)

Replaced old worn out parts with new ones.
Now it cleans like it should once again.

Remove old spring pin, spring, door
Waste of time effort and money didn't change a thing still won't dispense soap to wash dishes

put new seal in and it still leaked!hum

Came home and my husband had it all done. He said it was simple and it looks bran new again. Very satisfied.

Opened the door by using a star screwdriver. Pulled the door inside from the outside. Located the broken spring, put in new one (be very carefull to see how the insides are put together..makes life ALOT easier), and carefully put back together.

Removed and installed new door gasket which I found to be a simple task. Ran dishwasher and it still leaked. I then looked at other repairs submitted by your customers with the same problem. One had mentioned removing the lower spray arm and checking the screws around the pump. Sure enough, 2 screws were nearly ready to fall out and all others were loose. Tightened those, reinstalled spray arm, ran the dishwasher and no leaks. A big "Thanks" to you and also to other customers for sharing both their problem and how they were able to fix it. It sure saved me some money!!

I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

Followed vidio instructionson web site. Quick easy fix