DP840CWDW0 Whirlpool Dishwasher - Instructions

Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.

Remove lower rack in dishwasher, remove dishwasher, lay dishwasher on it's back, remove and replace motor and pump.Install new impellar with new seal. reconnect water, electrical and drain hose. Easy Peasy

i took the inside door off and took the 2 switches out and replaced them; not too difficult.

Trial and error. The spring was difficult to install, the pin and door were easy.

1. Turn off the electrical switch that powers the dishwasher. 2. Open the door of the dishwasher and find the two phillips head screws that secure the top of the dishwasher to the kitchen counter. 3. Remove the screws. 4. Gently move the machine side-by-side a bit while pulling it out onto the kitchen tile (be careful, the water-supply hose, electric cord, and dishwasher drain hose may not be long enough to allow you to pull it out very far - don't break or kink the hoses). 5. Remove (pull off) the black plastic fastener located on the bottom/rear of each side of the dishwasher. 6. Remove the old surround. 7. Lay the new wrap in place and secure with the two plastic fasteners. 8. Push back into place, secure the two screws, check your hoses.

I just followed the video, and it now works perfectly! Thanks SOOO much! great site, great info.

I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then just reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. Thanks for the video.

Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat head for leverage to finally get the screws out. Everything works perfectly for once.

Followed vidio instructionson web site. Quick easy fix

Replaced the faucet adapter, works fine

The bottom trim piece popped off easily and I removed the damaged panel and replaced it with the new one. I snapped on the trim piece and I was done. It took less than five minutes.

Watched your video and replaced seal in approx. 5 minutes, probably less. Still leaked so I looked at your page for solutions, found out where the air vent was and pried it open, very disgusting mess. With screw driver and long tweezers dug out what I could then poured a mixture of bleach and water in the vent. Totally cleaned it, very white, vent cover went into a bucket of bleach and hot water and it cleaned very well. Put vent cover back on and did a load of dishes, works fine. Thank you for having such a great website, if I ever need help again I will be back. It's a shame someone didn't tell you about cleaning the air vent when you bought the dishwasher.

I unsrew the faucet head, and attached th e adapter