DP470 - Instructions

After removing the cover to the motor assembly, I determined that the problem was that the old drive belt had broken. It probably was more than 20 years old. I originally thought that the size was no longer available because the old belt had stretched about two inches, but, after reading the repair stories on the PartsSelect Website, I decided to try the 25 3/8" belt. It worked great! After a few tries I was able to stretch the belt across the two pulleys without having to loosen anything. After applying the silicon grease, the dishwasher worked as good as new. The most difficult aspect of the job was having to work in such a small space. The most time-consuming part of the job was removing and then replacing the access cover, but the job overall was quite easy.

it was very easy to unscrew the broken nozzle and screw back the new one. !

Read thru the comments by others and matched them up with what I found (belt off the pulleys) when I took off the kickplate below the door. The old belt (20 years) had stretched about 1 1/2" compaired to the new replacement. Slip the new belt on the motor pulley and start it around the back of the pump pulley. Get your wife to hold your legs down so you can really twist/pull the pump pulley until the belt finally slips into place. No need to loosen the motor mounts if your wife can hold you down.

First removed the four screws to the lower front outside panel (the only tools needed to complete this job). Slide the belt under the drive motor, onto the motor pulley grove, then strecthed the belt onto the pulley for the pump that's on the power module (was qiite difficult, but with the directions supplied with the belt, was able to get it on) Lubricated the belt with silicon grease.

Removed the back - Saw the broken clips on the base of the dryer (the wires to the motor were pulling out because the motor was slipping).

Guessed that the parts were motor clips (no pix in the web site!)

Got the parts in post - they were identical except needed some rubber grips inside to hold tight (Used pieces of bike tire inner tube cut to fit for this.) Attached clips. Works fine!!

(Son is an engineer - he found the problem. Husband is a retired doctor - he couldn't!! but together they
supplied the muscle)
Sue (67 years old)

This dishwasher is over 20 years old and still works well. The door springs broke and the skematic shows 2 springs on each side. The spring kit only includes one spring for each side which is the primary spring. Removed the bottom access panel, shut off the water line and removed the water line. Removed the top screws which lock the dishwasher in the cabinet and pulled forward about 6 inches to fully expose the springs. Replaced the two big springs, one on each side and adjusted for maximum pull of door. The second small springs were not necessary. Pushed unit back into the cabinet, connected the water line and tested for water leaks. Cleaned and replaced access panel and the door is light as a feather.

I removed the access panel and it was right there. one screw - disconect the wires & it was out. then right back in - access panel on, and done.

Replaced the faucet adapter, works fine

I bought the portable dishwasher on Craigslist, and it didn't have the connector that goes on the kitchen faucet. Ordered it here, got it in a few days, and didn't need any tools - just had to screw it on. Good as gold!

I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and washed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!

I unsrew the faucet head, and attached th e adapter

Locked door closed, removed lower access panels with 5/16" nut driver, removed old springs with needle nose pliers, put plastic piece on top curved end of spring and placed on slot in door bracket as shown on instructions with part. Did same thing for the other door spring, used the screw driver to stretch the springs down to the first hole in on the base of the dishwasher on each side. Replace the panels. Job done!

replaced the faucet adapter I did not save when I change out the kitchen sink faucet set

Ordered a new Faucet Adapter! Simple

once i got it out the spring was a breeze