DGHX2655TF5 Frigidaire Refrigerator - Instructions

!st bin that came was broken when it arrived. It was only wrapped in a plastic bag inside the box. The second bin survived although wrapped the same way.....15 seconds to get it snapped in. Do NOT pull the fridge door shut with one finger on the bin!! LOL

First: I could not watch any videos. Big downer. Read the reviews and read a post about “three screws”.
Opened the freezer and emptied everything in it.
Remove the bin.
Two screws are on the left side. They go into the side wall.
Here’s where things get weird. The plastic “box” holds the “ice making assembly”. That box is attached by FOUR slots. You will need to remove the wire rack below the frame. There’s a plastic spacer on the left side with a slot on it. You can pull it of with your fingers when you rotate it. Slide the rack to the left and pull down the rack from the RIGHT side holes. You have move the box toward you about a inch, then it drops down.
Now, there is a electrical connection from the box to the rear of the refrigerator wall. You need a small screwdriver to lift the tab on the TOP of the connector to release it. Once that is done, slide the box forward and put it in the sink.
While all this is happening, the freezer is thawing out.
Once you remove the box, you will get error codes on the digital display. This is a good thing.
There are two “square head’” screws that you have to remove to separate the TWO parts that make the box. Slide the outer trim towards you.
The icemaker assembly slides into four slots. You put the new wires in the same place as the one you removed.
Put everything back together the opposite of the removal.
Now for the secret.
All that food you removed? Put it back in until you can slide the box into place.
Then you plug the connector in. The box should be sitting on the food.
THIS IS THE SECRET.
The ice maker has two options. Cubed or Crushed.
There are two components that make them happen. On the left side there is a slot with a gray lever the moves up an down. There is an piece of aluminum on the right side the drives the screw in the box.
Rotate the screw drive to 45 degrees.
THIS IS THE SECRET.
On the left side of the box is a rod that is spring loaded and has a bent end.
It’s about “timing”.
Find a piece of “kite string”. I used the string from the yellow energy tag that came with the fridge.
The box is sitting on the frozen food. The wire in the back is connected.
Loop the string around the lever AND PULL UP.
Slide the whole thing into place using the slots.
When it’s in place, let go of the string.
Put the two screws back in.

FINAL.
You have to PRESS AND HOLD the IceMaker button to reset. You’ll get ice cubes in a couple of hours. Through the first 24 hrs away.
You’re welcom.

needed replacements parts.

The repair was just as easy as ordering the part which arrived on day three after I ordered it! I had already cleaned up the broken glass insert, so all I had to do was unpack and lay the new shelf in. Took less than a minute!

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

Replaced the Triple Water Valve

Had to remove the refrigerated items off the crisper shelf to remove the glass, next removed the drawer to remove the crisper frame, then removed the middle drawer glass to remove the drawer, then the frame, installed the new frame cleaned the glass, re-installed the middle drawer, and continued the installation steps reverse of the removal process.

Replaced the top crisper drawer frame. Installation was very easy. The hardest part was cleaning all of the spilled food/liquid items from under the drawers once removed to replace the top frame. I will keep the top frame and repair it. From what I have read, this is a very common problem as there is no support in the middle of the frame...it is only plastic.

Looked at video on how to remove and reinstall support and followed the instruct ions

Glue the old one with gorilla glue. Made space and put the bin in. Now I have an extra one.

The most difficult task for me was getting old gasket out. I did call for repair help. The service person was most helpful. After almost giving up, one more tug and the gasket started coming out. Next step was cleaning the area. Aligning the gasket correctly made installation easier. I realized right away that I needed to start in a corner. The gasket went in without a hitch. My freezer is like new again. Next installment will be the refrigerator.

pushed bin into place

I ordered 3 bins initially and received only one, which was very easy to install. It just snaps in. When I called to indicate that I had received only one of the 3 bins, a claim was submitted and I got a refund for the missing parts. Then I had to reorder the two missing parts.

When I received the reorder, both of the bins were broken. I called to indicate that they were broken. I was told that I would have to submit photos of the broken parts to photos@replaceparts.com, which I did. After I submitted the photos, I received an email asking me for the photos again and the serial number of the refrigerator. This is the first time the serial number was requested. I have no idea why they wanted the serial number at this point instead of when I first ordered the parts.

At this point, I am still waiting to get my claim for the broken parts approved. I assume that the shipping department is pretty worthless, since they screwed up my order to begin with and then the shabby packing that was done for such fragile plastic parts on the reorder.

I'm not happy with the hassle that I have been going through just to get a simple order delivered.

Slip out old shelf, remove glass and clean, slip in the new shelf and replace glass on top. That easy

Replaced said Bin-Door.