DE170ADF2 Westinghouse Dryer - Instructions

removed top-removed front-removed belt-removed drum (I didn't know how the drum came out WITH the bearing so I unscrewed the 3 middle screws on the back of the drum which released it from the bearing)- removed the bearing-that was when I knew what to order. installed the bearing on the drum before assembling all in reverse order. I wasn't sure how much grease to use so I used about 1/3 of it.

I viewed the video from your site (Parts Select's) and followed those directions... which took the guess work out of the job and made it simple. Also the video alerted me to small ball bearing in the back which might have caused some head scratching if not for viewing the video. While everything was apart I did spend extra time cleaning. Many THANKS to Parts Select and the courteous parts person that I spoke with and placed my order with.

I highly recommend watching the repair video. I could stop the instructions and do the procedure then resume instructions for the next step. I would recommend you have a second person to help lift the drum up & out of the dryer frame. And ladies please instruct your husbands to watch the video all the way through. Mine lifted the top off the dryer and stuck his hand in and cut his finger immediately on a sharp piece of metal. You know because they don't need to read the instructions.

I followed instructions I found on u-tube to remove the drum and belt and access the bad bearing and change it. The instructions were quite good other than needing to remove a small panel on the back of the dryer to pull the belt around the tensioner.

Followed the video, it was good, the instructor's tips were useful and time saving.

Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.

It was super easy! I followed the PartSelect video and everything went fine. Getting the drum out of the machine was a bit tricky but once it was out, the rear bearing kit went in without any problems.

Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.

The video was very helpful. Glad I bought the entire kit. Dryer works great and no noise.

It was really easy to install the new roller with the newly designed side flange! All I had to do is hook in the tension spring. Works perfect again without the squeeking noise!

First I have to say that this was the fourth appliance repair I've done with Partselect parts. I am very pleased with all parts I've gotten from Partselect. The things I've ordered here are delivered quickly and are correct. Now for the dryer repair. I guess the most important tool I had to complete the job was the excellent video demonstration on the Partselect web site. I found that by following the instructions on the video even I had no problems. I spent more time cleaning the inside of the dryer than I did on installing the rear drum bearing. I probably saved us several hundred dollars by making the repair myself. At first I was intimidated but after I got the top off of the dryer and the front off the repair was simple and straightforward. Total time of repair was about fifteen minutes. Total time spent cleaning the lint and other stuff (I did find two dimes and a penny) was about forty five minutes. One hour total and my wife and I have a dryer which is acting like it did when we purchased it in 2001. Thanks to Partselect. Barry

I replaced the latch on the body and on the door and it worked very well. I had to watch the video first. Thank you.

The customer had removed the top cover hinges and the rear cover plate to recover the broken belt. I first removed the four screws holding the front panel and tilted it out to allow access for the new belt. The drum dropped about 2-3". Fed the new belt over the drum with the printing'This Side Up' facing me, lifted the drum up as I closed the front cover over the felt on the front rim of the drum. Replace dhtew four screws. Door switch leads were long enough to allow the front cover to tilt forward so did not remove. Next engaged the motor pully and tension pulley, then rotated the drum manually to assure tracking and no twist in the belt. Vacuumed the wall passthrough pipe,the flex vent tubing and the motor compartment of lint. Closed up the back cover and drove the 52 miles back to my shop.

Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!

I remove the drum, and install the bearing just like the instructions in the video.