DDE7100LA Hotpoint Dryer - Instructions

Parts arrived within a couple of days,the repair went fairly easy.

First unscrew the two screws at top to disconnect the control panel. Lay unit on the back. Remove door(be careful not to lose washers and hinges). Remove four screws to lift off top. Wiggle drum, slip belt over drum. Replace door, then put Four screws back in place.Stand unit upright.Remove back panel, you should see belt hanging.Pulley wheel is in front of you.Follow instuctions sent with pulley wheel.Reattach you're ready to roll, make sure you sllip the belt on the drum until the drum spins.

We removed the lid to the dryer. The drum had to come out so the back access was removed and the belt taken off. The drum then slid out the front. The dryer had two elements both were broken. The new ones were stretched to the proper length and laced through the ceramic brackets. The new copper leads werre installed and the coils attached to them. We cleaned the dryer as much as possible and reassembled it. Works like a charm (for now)!

I got to supervise - my son did it for me!!!! Went very well!

the switch was stuck couldn't get the switch to pop out to stop the dryer when opening the door light inside also wouldnt go on. it only took a few min to take it the switch and replace the new switch the light now works also stops when opening the door it made my day easierhow easy it was to fix it. only take to use a pliers and screw driver.

Make sure your power is off, When loosened the top and tilted back, the first thing I saw was the door switch, I guess I was just lucky I disconnected the two wires and checked it and it was bad. Got my new one from you and installed it. It has a ground terminal, which my model switch only had the two terminals. It working fine.I took the bad switch apart and the one leg on the copper U shaped contact had broken off. The Belt I have as a spare.

Change the coil by removing the cotter pin around drum in the back I accidently removed the 3 star bits and the front and it was hard getting back together. The coils are easy to change, but found that the coil wasn't the issue it was the cyclical thermosat underneath the lint catcher in front. The part (heater coil) works better than the older one, so I guess it wasn't a complete screw up. I read up on a few others and think I should have check thermostat first oops. good luck

Pop off the old, pop on the new. I did it with one hand, the 'hard' part was putting the access panal back on.

Researching on the web I thought the trouble might be lint buildup or trouble w/ one of the parts involved in spinning the drum. However I cleaned out all the lint and replaced the belt and idler pulley and this didn't improve the smell (drum bearing was fine). I then concluded the trouble was the motor. Running the motor w/o the drum in place confirmed this was where the noise/smell was coming from. Replacing the motor was fiddly--I had to remove the clip holding the motor (pried the top w/ a screwdriver), wires (made a diagram so as to put back in same order, they were hard to get off--a pliers did the job), clamps holding the motor on the duct, the motor mount, the duct, the fan. Putting all this back together took a while (not hard just fiddly). Tested the motor w/out the drum in place and it sounded fine. Put the drum and back/front/top panels back and the dryer runs fine now. All parts came quickly and exactly matched the parts in my 1993 Hotpoint dryer. As others have said the pulley kit is not needed--these are included w/ the motor. BTW I am a 53-year-old lady. Thanks to all who took the time to write up their experiences--big help!!

I suspected the idler pulley shaft was worn. I found the repalcement pulley on parts select web site. finding the part was very easy and delivery was very quick. After removing the dryer from the wall,I removed the access panel in the rear which exposed the motor, belt, and pulley. After removing the belt from the pulley, I removed the pully assembly from the dryer. I removed the keeper retaining ring on the pulley and installed the new pulley with the new parts supplied. The new pulley assembly was then ready for re-installation.

removed four screws holding top. Swing back top to expose thermostat. emove two push on connectors and two self tapping screws. Instal new thermostat

I have had this happen to another ge dryer, so I had an idea what was wrong. After taking the 4 torx screws out from under the front lip of dryer top, lifting the top back (like opening the hood of your car) in the back right corner is where the high limit tstat is. To verify the problem (dryer already unpluged of course) pull the two wires off the terminals of tstat, connect them together, wrap bare parts w/ electrical tape. Let top down & plug dryer in-- it started& ran fine. Got online and ordered replacement tstat (it arrived in 2 days-- great!) unscrewed the two 1/4" hex screws holding tstat on, installed new part. On to bigger and better things ! Dryer working fine.

take off door, take off front, mind the 2 wires for the door switch, take off top, take out enough screws on right side so it will lean out a bit for the drum to be removed. before removing drum you must remove the belt. pull the wheel to the right, minding the belt pattern for reassembly, its springy and will relieve tension. pull drum out. look to the left of the pulley and check to see any stray wire that may have pulled out while battling the belt. if you found a stray wire and it reaches the dryer motor find its home. on to the coils. I left assembly on dryer so I didn't have to figure out wire placement. the end connectors that the coils attach to are to be reused so don't get to mean with them. remove the end connectors minding how many wires it has and which of the 2 coils go to it. remove the old coils so as not to damage the very brittle ceramic insulators. on to the new, the instructions will tell you to stretch out the new coils to specified lengths. start with the shorter one first! just to see the stretchiness and how far is too far to stretch, if to long it will touch the heat shield and no good can come of that. after stretched out its time to string new coils in, carefully, so as not to stretch or collapse the coil. now hooking the end connectors to the ends of spring. I used 2 pliers to bend the tab a little bigger so it would cover the spring end. after springs are attached to ends and ends are in place, time to battle the drum and tensioner again, make sure plastic piece is on drum insert if equipped, put drum in place and bend tensioner down and install belt. put side screws on, then front and 2 wires , then top then door. plug in and start up. if unit doesn't start remember that stray wire going to the motor, you guessed it wire goes to the start switch. unplug and hook up the wire and it will work.