DDC4580NDL General Electric Dryer - Instructions

I read all the reviews first, and decided on the best method, which is, disconnect utilities, remove four phillips screws under front of top,swing top open like a box lid, pull the two spade connectors off of the door switch, loosen the two hex head screws under the front of the front panel,remove the 2 hex head screws near the top of the front panel, and free the wire harness along right side of machine, this will allow you to swing the entire front panel to the right side,now remove the three torx screws inside the drum,this will allow the drum to be removed, exposing the bearing assembly at the rear of the drum. My machine is 20 years old, and when ordering parts, my machine #s were not listed, but they looked identical, but my bearing's shaft had a circlip retaining it in the bearing receiver, which had to be removed,( the newer shaft just inserts into the receiver, which is screwed into the back of the machine). Make sure to install the ground strap like the one you removed.My best advice for someone thinking about this repair, take it apart first and survey the parts needed before making the decision to repair your old machine, my drum's old bearing allowed the machine to function, and the shaft wore through the bottom of the receiver, allowing the defector, a round disc of thin sheet metal at the back of the drum (a $128 part), to make contact with it's housing, severely damaging both parts, making further investment in this machine unwise,even if I replaced the disc, the cut in the back, would allow really hot gases to escape into the dryer's interior, a scary scenario. I cut my losses and bought a new dryer last week. Anybody want to buy a brand new rear bearing assembly & belt for a GE dryer?. If you only have to replace the bearing, the job is a snap, but prepare to do a lot of dust removal!. Steve

Key starting point is to remove top cover by removing two long screws located at the front of the cover
Remove control panel and it's bottom and side supports.
Remove short vent pipe by bending retainer tab.
Support the drum at the top using piece of rope.
Remove main rear cover (leave bottom attached).
Remove electric heating unit and install new bearing carrier from kit.
Reinstall the the heating unit
Remove three screws (inside the drum)to release the inner drum cover and release the bearing carrier.
Install new bearing carrier. Note: the three holes in the bearing carrier are not tapped, I suggest that the screws be installed (threads cut) into the bearing cover before attempting to install the bearing carrier.
Install the new bearing carrier. Note: pilot one of the holes using a small nail etc. then go on to install screws in the other two holes remove the pilot device and install the third screw.
Reassemble in reverse order.

Remove top panel and front panel. 12 Screws. Be sure to vacuum entire inside of cabinet free of lint.

I followed the instructions in your detailed online video. Fortunately on my model there was a removable panel on the back of the dryer which provided easy access to install the drive belt on the motor pulley and the idler pulley. Great video and very easy repair.

This is the third time for a belt on this 28 year old dryer. Not too much to it. Unplug the dryer. Open the door. Remove the screws holding on the front panel and loosen the screw at the bottom. Disconnect the wires to the door switch and lift off the front panel and start up the shop vac to clean out the lint - there is a lot to be found in various places. Slide the new belt over the front of the drum and make sure there are no twists. You can now reverse the order to mounte the front panel but don't close the top so you have light to see inside. Go around to the back panel and remove the machine bolts holding on the access panel at the back. This allows access to the motor and belt tensioner. Get the shop vac out here and get to some more lint. Google the model number to find a diagram on how to route the belt. Put the belt on the motor shaft and around the tensioner as depicted. Occaisionally the plastic idler pully is worn and this can be the cause of the brokent belt. If the idler wheel does not spin freely, squeads or is cracked it should be replaced or you will be right back replacing the belt again. If all is fine it is time for a test run. CAUTION - you can plug the dryer in but keep your hands out of the cabinet as there are live exposed 220 volt terminals exposed. This allows you to observe that all is working and not binding during a test run with NO heat. If all is fine, unplug the dryer and put the covers back on. Reconnect the exhaust hose (now is a good time to clean that and the vent to outdoors as well).

I removed the 2 screws and lock assemblies from both sides on the back. Then i removed 4 screws (two from each side) on the control panel and lifted that up as i tipped the cover forward to disconnect the wires from the door switch. I found the wiring diagram inside the control panel cover, which included a belt routing diagram (very helpful, being the belt was laying in the bottom. I then removed 3 torx srews holding the drum to the bearing, and removed the drum. Let the fun begin! i proceded to put the belt onto the motor pulley and around the tensioner. i needed some help from my wife to set the drum back in as i held the belt up around it. once the drum was back in, i found the beld had fallen away from the tensioner. I lifted the front of the drum up just enough to get both arms below it and move the tensioner back to slip the belt over it correctly. With the new belt on i started to put the screws back in the drum. This got very frustrating, as you have to correctly line up all the holes again, while holding the drum in the correct angle to start the screws. this was the hardest part, not physically, but wears on a person's nerves quickly! Once all the screws were in and tight, i took a deep sigh of relief before i tipped the front cover up just enought to get the wires hooked back up for the door. I turned the unit on to verify the repair before re-assembly. Yep! works again, for well under $20.00! Thanks PartSelect!

Unplugged dryer, disconnected gas from igniter sleeve and removed sleeve (AFTER you unplug all wires). Replace the igniter "very carefully". It is as fragile as bare pencil lead. Replace the igniter sleeve. Beats the snot out of buying a new dryer. Thank you for having the parts.

Found excellent instructions and diagrams online by searching under the model number. Best of all was the service from PartSelect. Belt arrived 24 hours after ordering. It was the right part, it was easy to install, and the dryer is running beautifully.

just changed out the gas igniter very simple to do thanks

Took the top and front off. DO NOT TAKE DRUM OFF!! Lifted drum slightly and worked belt around drum. Replaced front and top. Took off rear panel at bottom near vent pipe. Put belt around motor and then tension pulley. Buttoned everything up and that was it!

I wanted to be sure a replacement would be available when the need arose. The dryer might be 30+ years old. Within a very few minutes I found the filter and placed an order. It arrived in 2 days. Now I won't have to worry about it in this aging lifetime.

Just took it out and installed the new one--thanks so much

Replaced filter

First I shut off the gas and unhooked the gas line. Then opened the door and removed the screws that hold the top down in the front. I then tipped the top back so I could get to the top of the drum. I removed the screws ( 4 ) inside the door opening and slid the felt seal back. Next I put the belt in the drum and feed part out the crack between the drum and the dryer frame, being careful not to cut the belt. I woorked the belt around the crack and pulled it toward the drum. When I got the belt through it was all the way around the drum and I just put the belt over the motor pully and pulled the tensioner back and wrapped the belt over it. Put all the screws back in and the back on and fired it up. Works as good as it ever did.

The first thing I did was move the dryer out so I could "unplug it" !
Then I took the 4 philps head screws out that hold down the top of the dryer, then I lifted up the top and moved it off to the side making sure the wires didn't get pulled out.
Then I removed the 2 5/16 cap screws that holds the front panel on and lifted that off "Make sure you mark the down were the 2 wires for the door swich go" Like white on pin 1 and yellow on pin 2!!!
The next thing is to slide the drum foward so you can remove the element package then remove the 3 philps screws in the back of the drum make sure you have someone hold the element package there is a sheild between the drum and the element package that may fall that is a watch out you will need to move the element package up so you can work on it there will be wires hooked to this ring so becare full you don't break them off.
remove the element package you will see the bearing kit attached to that.
There are 4 5/16 cap screws that hold the bearing kit to that remove them and then remove the old bearing kit you may find and E Ring holding the old bearing kit in place (this would be found in the older models).
Before you install the new bearing kit take the new self tapping screws and tap the holes in the new bearing kit mounting plates this will make things go faster!!!
Now mount the bearing plate with the 4 holes to the element package there is a tab that needs to be mount in there too so look at the old one when you are taking it off.
Pick up the sheild that fell pick it up have a second person help you hold everything in place while you line up the holes for the front plate to the back of the drum and start your screws.
Now tighten them down check to make sure your belt didn't slide off the tensioner that is next to the motor before you slide the drum back in place if it did take the time to figure out how to get it back on the right way our you will be pulling things apart again.
What I did was spin the Drum by hand to make sure everything was ok. you will know if the belt is off it will not move when you spin the drum by hand.
Now that you made sure the belt is on you can put the front back on there are 2 studs on the bottom that you need to set the frount panel on before you can put the screws back in in it.
Now that you have the fron back on it hook your 2 wires back up to the door switch like you took them off!
Now move your top back over and you will see 2 clips on the back of it that slide into a grove in the back now that you have that in place start putting the screws back in put the middle 2 in first and tighten them down them put the last 2 in.
Now plug it back in if your vent pipe fell off hook it back up as you slide your dryer back in place now try it to make sure everything is working right and you will hear the differance.
Good Luck with your repairs....
Just a quick note this dryer is over 40 years old and still going.
I have replace 6 elements and 1 drive belt since it was bought new now the bearing kit.
Clean it once a year and the vent pipe every 6 months it will last!!!