Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The upper drum glide is attached to the front panel of your dryer, you can locate it by removing the top portion of your dryer. The drum glide allows the drum to rotate with ease and little sound. The...
The door strike is attached to the door of your dryer and holds the door closed. If your dryer door is not closing, this might be due to the door strike needing to be replaced. This is a simple repair...
Introducing the GE Dryer Drum Bearing! This genuine replacement part is the ultimate solution for enhancing your dryer's performance. It is ideal for supporting the drum as it spins, offering stabilit...
This part is found in the same location as the Terminal Block at the back of the Dryer. It acts as a safety device which prevents your appliance from overheating.
Unpluged dryer. Removed the top of dryer by pushing in a retaining clip on both sides of the front lip with a screw driver. Remove the two screws on both sides of front panel. These screws are square head or phillips #2. Unplugged the wiring harness to front panel (make sure power has been disconnected). Support drum and lean front pa
... Read morenel away from dryer body. Front panel will pull off of tabs at bottom. The old drum glide is fiberous and hard to remove. I removed most of it with the pliers, but had to carefully scrape the balance of the glide off with the wood chisel. The adhesive that comes with the repair part has an acetone base, so I used acetone (or you could use nail polish remover) to remove the old adhesive. Once the acetone has dried, I applied an 1/8" snaking bead of adhesive to the front panel. There is more adhesive in the tube than you need so do not use too much. Make sure that you get adhesive as close to the base of the lower seal as you can. Follow directions on adhesive tube and then attach the glide. I let it set up for about 30 seconds. Place the front panel back on the tabs of the dryer. Carefully lift the drum an fit it on the front panel and insert the two screws holding the panel to the base. Reconnect the wiring harness and make sure it is not in contact with the drum. Check to make sure that all of the electrical connectors on the timer are still in place. Reassemble the dryer. Reconnect power.
1) Removed Top Dryer Cover (pushed 2 compression clips on front side 1" from top and 2" in from each side) to gain access to terminal block in rear. 2) Removed 2 screws over terminal block cover and 2 screws holding bad terminal block in place. Removed 3 screws holding bad power cord, 3) Removed good terminal connectors from
... Read morebad terminal block and reinstalled them in the new terminal block. 4) Cut dryer wire from bad terminal block connector and soldered (optional) them to the new terminal block connector. Installed this connector into the new terminal block. 5) Installed new terminal block in dryer with 2 screws. 6) Installed new power cord on new terminal block ensuring contacts were tight and cord had pull guard properly installed. Reinstalled terminal block cover with 2 screws. 7) Reinstalled Dryer Top Cover.
1) Disconnect dryer from power. 2) Use a large standard screwdiver to push in 2 clips on the front side of the dryer between the main body and hood. Hood then lifts up on hinges mounted in the back. Secure hood. 3) Pull off timer knob and remove 2 screws. 4) Write down the color sequence of wires attached to old timer.
... Read more />5) Remove wires to old timer using needle nose plyers grasped at the wire connector. 6) Attach wires in the correct sequence to new timer and reassemble dryer.
