Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for ...
This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if...
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
This light bulb, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can so...
This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep yo...
The drum slides are not included with this part. The top bearing helps your dryer operate as quietly as possible. This part will require two green drum slides and 2 white drum slides.
This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on ...
This rear drum bearing sleeve is a critical support component located at the back of the dryer drum, designed to reduce friction and ensure smooth rotation during operation. As the drum spins, the sle...
TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the...
This authentic OEM rear bearing O-ring is designed for use with GE dryers. It helps secure the drum rear bearing onto the drum shaft, playing a key role in maintaining smooth and quiet dryer operation...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeffrey
December 26, 2019
The unit starts and heats 1/2 the way through the drum stops but timer stays going what can be the problem its a new motor
For model number DCVH640EJ0WW
Hello Jeffrey, thank you for your inquiry. Most likely the problem is the High Limit Thermostat. This part cuts off power to the dryer motor if the temperature reaches an unsafe level. For your model DCVH640EJ0WW, the correct replacement part is PS267900. We hope this information helps!
2 people found this helpful.
Did this question help you?
Thank you for voting!
Kristi
January 18, 2020
I was fluffing pillows in the dryer. I noticed when I pulled the last load out, one was stuck against the back of the dryer wall. Then, no heat. I unplugged, ran the codes but I either cleared it by accident, or there were none. The t07 test got to 76 degrees.
For model number DCVH640EJ0WW
Hello and thank you for writing.
It certainly sounds like it could be a faulty control thermostat PS1766014 and/or possibly a faulty high limit thermostat PS267900, you should check for signs of damage, and replace as necessary. We hope this helps. Please contact us anytime if you require further assistance.
It stopped during working circle and have no power after that. Please help me figure out what problem and how to fix it . I try to check on the fuses but don’t know how to take off the back panel…, Please help me, thanks
For model number DCVH640EJ0WW
Hi Nahn,
Thank you for your question. If your dryer will not start, there are some parts that you will need to check to see which one is causing the issue. You will need to check the door switch, the electronic control board, the motor and the terminal block. We have included a link that you may reference on how to check these parts. Once you have determined the part you need, please feel free to call customer service. We are open 7 days a week and anyone will be happy to assist you. We look forward to hearing from you!
Dryer on Ultra Low Heat runs for a while but there is still is heat coming out, after 15 to 20 minutes it stops running and won’t start again until it cools down. Are there any tests that will isolate the sensors that might be bad
For model number DCVH640EJ0WW
Hello Jeff, thank you for contacting us. The issue could arise due to a faulty inlet control thermostat, part number PS1766014, or a faulty heating element, part number PS9494500. If these parts are okay, you may need to check the high-limit thermostat, part number PS267900, for continuity. You can check all these parts for continuity with a multimeter and replace them if they do not have continuity. We hope this solves your problem!
Hello, my dryer is no longer heating clothes when it runs its cycle, what parts would I need to look into replacing to fix this problem ? My dryer is a front load dryer a bit different than normal dryers I’ve had before. It also has a little drawer on the bottom, while the buttons are all above the door
For model number DCVH640EJ0WW
Hello Shaun, Thank you for reaching out. We suggest testing the Inlet Control Thermostat,
High Limit Thermostat, Safety Thermostat and the Element with a multimeter to check the continuity. We hope this helps, good luck with the repair!
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and
... Read more drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
1. Removed top cap on lid by removing the 3 - phillips screws. 2. removed front digital display panel from PC board. 3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit. 4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this fram
... Read moree. 5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides. 6. Re-installed all wiring and panels.
*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on. This was a first attempt ever at fixing an appliance and it was no big deal.
