This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for ...
This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if...
This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the ground strap. This part helps keep yo...
This light bulb, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can so...
The drum slides are not included with this part. The top bearing helps your dryer operate as quietly as possible. This part will require two green drum slides and 2 white drum slides.
This door latch is designed for your dryer, and is mounted to the dryer frame. The door latch holds the door of your dryer closed while the machine is operating. If your dryer door is not catching on ...
The interlock switch may also be referred to as a belt switch. This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open. This is a part for your dryer. ...
TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the...
$8.54
In Stock
Questions And Answers for DCVH515GF0WW
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Colleen
December 21, 2019
My dryer shuts off after few min of start up to dry.When the front panel is hit, it starts working again.
For model number DCVH515GF0WW
Hello Colleen and thanks for writing.
It certainly sounds like a failed door switch PS2344321 you should check for signs of damage, and replace it if needed. We hope this helps. Please contact us anytime.
I have a electric model DCVH515GF0WW that has no heat.
For model number DCVH515GF0WW
Hello Nick, thank you for your question. We have researched your model and found that the most likely fix to your problem is to change the primary dual coil gas valve, part number PS268153, and the secondary coil, part number PS268154. If you require assistance to place an order, please contact customer service. We hope that helps!
Hi Patricia, thank you for contacting us. We have found that the issue is probably because of the thermistor, part number PS11721518. To fix the issue, we would recommend replacing the thermistor. We hope this solves your problem!
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and
... Read more drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
1. Removed top cap on lid by removing the 3 - phillips screws. 2. removed front digital display panel from PC board. 3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit. 4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this fram
... Read moree. 5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides. 6. Re-installed all wiring and panels.
*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on. This was a first attempt ever at fixing an appliance and it was no big deal.