DA6200 Speed Queen Washer - Instructions

1. Removed hoses 2. Removed inlet valve. 3. Took valve apart to discover defect in diaphram. 4. Looked up and ordered part. 5. Replaced inlet valve. 6. Tested washer.

I followed steps outlined on you web page.

Removed old valve and replaced with new. Wire for wire..screw for screw..

I checked the inlet hoses for hard water build up and noted that this was not a problem. Then checked the hose from the inlet valve to the washer drum and determined that it was clear so I knew the problem was a faulty inlet valve. After receiving my replacement valve, I removed the old valve by removing the hot and cold water hoses and unscrewing two screws securing the inlet valve and lifting the inlet valve out the metal holding bracket. This gave me complete access to the inlet valve allowing me to remove the hose clamp and hose to the washing machine drum. The new inlet valve was an exact match so I removed the four electrical wires one by one while putting them back on the new inlet valve to insure correct electrical connections. I added a piece of one half inch plastic tubing provided with the new inlet valve on the outlet nipple of the new inlet valve to prevent leaking. I then put the new inlet valve back into the holding bracket and screwed it down. I replaced the hot and cold hoses to the new inlet valve carefully so as not to cross thread the plastic connection on the new inlet valve. After turning the water back on, I checked for leaks and plugged the washing machine back on to test it with a washing cycle.

took hose off then took three 5/16 screws then clamp off reversed order to put back on check for leaks ok

I took the hot and cold water hoses off with pliers.and then I took the one screw out towards the top of the water inlet valve plate.disconnected 4 wires,there is a small clamp on the small hose on the valve you have to remove.and last there is a cluster of wires that has to be removed from a bracket and (it is important to put these cluster of wires back in place otherwise they will wear a bare spot in them.)

I ordered the water valve at 12:42 PM one day and received the part at 10:25 AM the next morning. Now this is what I call excelent service. The price of the part was very reasonable. Getting my wife off my back for her washer being broken PRICELESS.

Removed three screws - Disconnected both inlet water hoses-Disconnected 4 electric clips-Removed internal hose connection from the same unit- Reverse order in assembly.

The repair was simple, and followed the instructions exactly. Removed three screws, one small hose clamp, and two electrical connectors. Replaced and reassembled. Worked like a champ!

My experience with my repair is as follows:
After determining the "hot water" solenoid was weak and that a new fill valve was needed, I placed my order with PartSelect on Thursday and to my suprise, had it in my hand Friday evening (no special shipping). WOW talk about fast! But unfortunately the part was broken.
Called PartSelect back Saturday morn to explain my problem and was told that I would be credited for the broken part and that a replacement would be sent ASAP probably arriving on Wednesday. Again to my suprise, the part arrived on Tuesday morning.
Hats off to you guys for great service, prices and no hassles.

Dennis Fleming
North Billerica, MA

Exactly as the video showed. This was a very simple repair. The only extra thing I did was to replace the mesh screen/gasket at the hose ends. They were plugged with crud. PartSelect saved me from buying a new washing machine. Yay!

pulled the front panel first, then lifted the top(2bolts in each).
Then unhooked water and unbolted the water inlet valve from the back left corner behind the tub.four wires are connected Pay attenion to where they go, for easy reinstallation.NOTE: watch the clips in the front of the washer they flew off and it took half an hour on the internet finding out how they went back on.

I watched a sample repair on YouTube and read the instructions that came with the part. All went as planned/described.

Removed door panel to get to the electric control conponents and noticed a burned wire to one of the door microswitches. Ordered the door switch repair kit from PartSelect. Also, ordered and replaced the thermal fuse at the same time since it was only $12 and didn't know if that blew at the same time the switch cooked. I had the parts coming standard delivery (3-5 days), but they arrived the very next day. Parts included easy to follow directions.Job went pretty smooth and the dishwasher works again Good experience!

Removed old part, installed new part. tested machine. worked fine.

First I remove the hot & cold water hoses using an adjustable wrench. I then unscrew the panel that holds the water inlet valve using a nut driver. I then carefully pull out the panel, moving the harness wires out of the way, so that I can loosen the clamp holding the inside rubber tube. I remove the old water inlet valve from the panel by removing the 2 screws and then put the new one in. I then reconnect the rubber tube and tighten the clamp. I then screw back the panel and reconnect the hot & cold water hoses. It took me about 20 mins to complete the job.