D-150 Hardwick Range - Instructions

I removed the heating element and noticed that the prongs were corroded. I looked for a model number but couldn't find it so it made it difficult to find a replacement until I got on this website. I found the replacement part and also found that as I checked for other sites for this part this company was the most resonable priced.
The part arrived and I replaced it in seconds. Turned it on and it worked immediately. Super easy.

I removed the old and repaced with new. I never ordered anything one day and got it the next. I'm impressed

Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering processes were simple and delivery was faster than I hed expected.
Thank you

Removed burner and then burner pan.Then replaced pan and reinstalled burner.

Package arrived while I was working at the computer and my husband announced minutes later, "That's what I like to see". I didn't know what he was talking about until he tossed the packing list on my desk and said, "It works perfectly. Good Job!" It had only taken a minute to pop the new parts in and he already had water on for coffee.

i read the installation instructions and followed them. first i made sure that each heating element was off. next i carefully removed each one (a total of 4) from it's plug and lifted the worn out drip-bowl up and replaced it with the new one. finally i pluged in (a total of 4) heating elements and turned them on to make sure them were working and they did.

This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.

Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.

Was glad to get the correct ones for a 30 year old stove. Had already wasted $12 shipping trying to order from someone else.

Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!

replaced the drip pans. Fit perfect. No problems

Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts together with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.

Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube over the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.

First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They work very well now.

I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...