Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer tub was not spinning
Smelled burning rubber, checked belt. Belt was cracked and worn out. Easy repair. Removed front of the machine held together with two screws at the bottom of the unit. Removed top cover of machine (the part with the lid). It just pops off. Pushed tensioner wheel in and took off old belt. Putting new belt on was super easy. Working like a champ now. $20 total with shipping. Not too bad to save a washing machine.
no problemO top loader. open top, disco two electrical plugs and a small hose, then remove two screws that hold valve in place and remove. Re install in reverse order. Thanks for your support Eliot in Alaska!
I just popped up the top front using a large straight (slotted) screw driver, then removed the 2 screws at the bottom front, then the whole front panel popped down about a half inch to be lifted out of the way. I found the old drive belt way down under the motor (still attached as normal), very near the floor and removed the worn out belt by hand, and replaced it with the new belt by hand also. The spring loaded belt tightener- idler wheel makes this a very simple process to accomplish. Then, I replaced the front panel-- all done. Works like new.
unplugged machine. pried up with large regular screwdiver on top washer lid. removed two phillips screws bottom of front panel, had to use rubber mallet to drive front panel down to remove as was rusty and old. removed old belt using screwdriver. put new belt under tub pulley and put belt on small pulleys. kept moving tub and springs by pushing on tub. Took several tries to get new belt to go on the large tub pulley but finally did it. I used the instructions you gave for replacing broken drive belt and it worked. replaced front panel and two phillips screws, put top back on and away it went.
Put machine on dolly. Tilted it on its back. Put screw driver into sheared leg and unscrewed broken leveling leg. Then screwed new leg in and tilted machine back up.
The water did not drain at all . You could hear the pump spinning , but it was not .
After making sure there was no blockages and the pump was not jammed I knew it was time for a new one . Unplug the machine and turn off the hot and cold water . Remove the two screws on the bottom of the front of the machine and push down on the panel it should come right off . Make sure all the water is drained out of the tub use a wet/dry vacuum to suck out all the water if needed . Then with the vacuum empty squeeze the clamps that hold the hoses on the pump and push them out of the way . Use the vacuum to suck up any leftover water, as you remove both hoses . Unplug the one set of wires going to the pump . Remove both screws and the pump should now be loose . Do the same thing in reverse to install the new pump . Other than dealing with the water it should take under 15 minutes . Good Luck
Pry up top from front remove 2 phillip screws at lower front panel slip belt under tub pulley then around motor pulley push belt tensioner towards back of machine slide belt onto tensioner pulley. (Done)
After struggeling the most with lifting out the inner drum and then the wash drum. I realized when the job was complete a better way. 1. Take the top off the washer. 2. take the front off the washer. Then disconnect all wires and hoses from assembly One small hose on the tub and the pump hose at the bottom. 3. at the bottom of the overall assembly there are 3 braces holding the tub assembly with 2 springs on each brace. Go under and remove the springs and then lift the whole assembly out into the middle of the floor. 4. remove the top cap off of the agitator. 5. remove the agitator. 6. if you are lucky and the bolts are not seized in the block that holds the shaft remove the small steel block from the bell and remove the bell. 6. Slide the inner tub up and off the shaft and again if all goes well the outer wash tub should slip up off the shaft as well. 7. remove the drive belt from the motor and transmission.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom "Screw", which is the front leg of the washer was broken.
Tilted the clothes washer back to provide easy access. Then after scrubbing the floor - which took most of the time of the repair, screwed out the broken leg and screwed in the new leg or SCREW. Easy peasey.
Washer would only let cold water in,then not fully cycle
Disconnect power,take water hoses off using pliers,they are really tight,remove 2 philips head screws,pull 2 wire connectors off and water fill hose squeezing wire clamp and sliding clamp back on hose.reverse to install.Works like a champ.
We have a washer/dryer stack type. For a week or so, my wife mentioned that washer is louder than normally is, shortly, the washer stopped spinning and the clothes were finishing soaking wet.
I opened the front panel sheet and saw the broken belt, ordered the belt online. The belt arrived in 2 days, and the actual belt-replacement took 10 minutes. The washer functional like new.