CST20KABCAD Hotpoint Refrigerator - Instructions

Remoed bottom hinge and replaced broken cam riser. Replaced Bottom hinge.

Used (2) 2 x 4's as block and lever to raise door removed 2 screws and removed door used same socket to remove and replace door side of replacement part. replaced door. This is the second time I have replaced this part on frig. side. Very easy replacement.

Emptied contents from the door. Removed top hinge cover (one screw) and top hinge (two bolts.) Lifted door off and replaced broken cam riser on bottom hinge. Put door back on.

replace broken hinge.

Removed shelf and vegy bin removed two screws replaced slide rail with new one and replaced the two screws and shelf and vegy. Bin and I was done. Ten mim. Tops

Emptied door shelves and removed top pivot hinge bracket. lifted door of lower pivot and set aside.

Removed vent-toe base and replaced hinge 'L' bracket and cam.
Removed two bolts from bottom of door and inserted new plastic cam.
Set door back on lower pin and re-attached top hinge bracket while aligning door.

Replaced articles back in door and watched it as it it self closed. Total time, less than 15 minutes excluding cleaning of equipment while dis-assembled.

Part Number: PS290199

1. Empty the door shelves.
2. Leave the door closed.
3. Remove the grill directly beneath the doors.
a. It snaps in. Pull simultaneously on the outside edge and the bottom about 2 inches in from the outside edge.
4. Using two people. One holding up on the bottom of the door. The other removes the two screws that hold the hinge to the refrigerator.
5. Open the door slowly and let it down slowly to pull the door away from the top hinge.
6. Replace the new hinge half on the bottom of the door. Insert the other half of the hinge into the hole of the door to keep the other half lined up while tightening the screws.
7. Apply a small amount of lithium grease to the contact surfaces of the new hinge.
8. Using two people. One person is to hold the door. Best if he/she holds it from the bottom. The second person lines up the top while pushing up on the door to insert to the top hinge.
9. Insert the other half of the new hinge into the bottom of the door.
10. Line up the holes and insert the two screws that hold the bottom hinge to the refrigerator.
11. Reinstall the grill.

Removed trim cap at top of door. Removed two hex head screws and lifted top hinge off door. Lifted door off lower hinge. Unscrewed broken cam riser from bottom of door and replaced with new part which was then screwed into place. Replaced door on lower hinge, Replaced upper hinge onto top of door, replaced screws and replaced trim.

Easy peasy. :-)

Followed other messages to complete fix. Simple overall.

Please note that if you buy the hinge assembly, you get spacer parts that mate. If you don't you have to hack-saw the rivot off the old hinge assembly to do your repair. Hinge assembly cost more but less work.

Discovered the door cam was broken. Did a search, found the part on PartSelect.com. Read the repair stories and realized I need two cams. So I just bought the whole hinge assembly figuring it would be a little easier and did not cost that much more.

Put blocks under the door, unbolted the old hinge from the refrig, and the old cam from the door. Replaced them with the new parts, and I was all set. Took about 15 to 20 minutes. Had my wife stand by the door just in case it fell, which I knew it wouldn't.

Don't even need to empty the shelves in the door.
Just prop the door up with a block of wood from the floor to the bottom of the door. Lay on the floor and replace the parts.

The door was acting up for a long time. I wish I had researched and repaired the problem a long time ago. Now it works great!

Same as the others, just propped the door up and took off the upper and lower hinge parts and replaced them. One note: the old hinge was so torn up that some of the shims were partially destroyed. Since I didn't order the shims, I had to do a little machining. It might be a good idea to order shims if there is ant doubt.
P.S. With normal shipping, the order arrived in 2 days!

I simply followed the excellent video, once I discovered the lower door hinge was the problem. Part Select was amazing! A $25 part and 15 minutes saved me $1,200+ ... the price of a replacement refridgerator. Thank you!

I watched the video on your web site first.Then I proceeded to do the repair exactly as the video showed. Very easy!!!!!

The refrigerator door would now close and notice broken plastic on the floor. It is a 1990 or so GE fridge. To repair - ordered the Cam Riser (the plastic piece that broke and the matching lower door bracket.

Took off the lower hinge with a socket wrench. removed the door. Replace the old Cam Riser with the new one. Slid the door onto the upper guide then fastened the new hinge with the socket wrench.

Easy job .. around 20 minutes.