CSK22GABEAA Hotpoint Refrigerator - Instructions

This is a side-by-side unit. After blocking up the closed refrigerator door to the correct height to match the freezer door, I removed the lower hinge pin assembly by taking out two bolts. Save the shims (my had two) for the new hinge pin. Then remove the cam riser from the bottom of the door by taking out two bolts. Install the new cam riser on the bottom on the door. Then install the new hinge pin assembly. Total time 15 minutes.

blocked up refrigerator door.removed old hinge, and put new one on,with socket set.

It was really easy for me....my son told me what part I needed. I ordered it, and he installed it!

I removed all the items off the shelves of the door. I then removed the top assembly,Then lifted the door off the the bottom hinge and laid it on a flat surface. I then removed and replaced the cam connector on the bottom of the door. I then removed and replaced the cam from the lower right side of the refrigerator. I put the door on the cam without assistance , then reassembled the top assembly. The refrigerator door operated immediately just like it did when it was new over 20 years ago.

Several months ago I had to replace the hinge and cam on the refrigerator door and the repair went smoothly as pictured in the video. This time I had to replace the cam on the freezer door so I ordered the hinge assembly, which included the cam. The web site confirmed that, according to the model number of my 27 year old refrigerator, the hinge assembly would fit. The problem I had was that the top hole in the hinge was positioned too high to fit the hole in the refrigerator so I had to put the old hinge back on, even though it showed some wear. The door closes smoothly by itself now.

I just followed the video instruction supplied by PartSelect and the whole thing was a breeze.

Removed freezer door, put a blanket over the opening to keep food frozen. Installed hinge and replaced door.

Removal was easy. The problem was that the old hinge had screws approximately 3/4 inch apart. The new hinge assembly had screws 1 inch apart. The threaded backing plate matched the 3/4 inch spaced old hinge but would not line up with the new one. There was a hole in the refrigerator frame but no way to hold the screw from the back. I had to fine a bolt and nut that would fir and still be heavy enough to hold the weight of the door. This repair took place at my cabin--miles from any hardware store. I found a long enough bolt and nut but it was a little too big for the hole in the hinge. I had to drill the hole in the hinge out so it would fit. Trying to reach the back of the bolt with a nut was a problem. I used tape wrapped backwards on my finger to hold the nut and then reached around to start the bolt into the nut. It too a few tries but I finally got it. Bottom screw was not a problem. It took about an hour and a half to fix the door but it works fine now.

on the refrigerator side remove two screws from hinge on top of door, pick doorup to remove from bottom hinge using a 5/16 socket remove the two screws holding hinge in place, replace with new hinge. on the door loosen up the screws, no need to remove. the screw closest to the hing axis remove completely remove the old cam, insert new cam lined up with axis of hinge reinsert screw, place door back on hinge and replace hinge on top. the freezer side has water an ice in the door.at the bottom [grill has been removed] of the door a plastic tubing has to be disconnected [make sure water is off] the disconnect is near the door, the coupling is only finger tight. uncou[ple plastic coupling and pull out of connection, pull the nut and ferule off the tubing. now take top hinge off, remove door straight up while feeding plastic tubing thru hinge. the hinge is replaced the same way as the other side. when new hinge an cam are in place, lift door up now feed the plastic tubing thru the hinge till door is in place, replace top hinge. when you reconnect the plastic tubing it helps if you place a lubricant on the end so that you slide the nut and ferule on. the connection should only be finger tight, no wrenches

This is a side by side freezer/refrigerator, nearly 30 years old. The repair was very quick and easy. 1. Remove two screws from top bracket. There is no cover for the top hinge on this older model. (2) Lift off door and set on kitchen table. (3) Remove two screws holding bottom door hinge. (4) remove two screws hold the cam and shims on the bottom of the door. (5) replace the broken cam on the door, and the bottom hinge assembly. (6) Replace the door on the bottom hinge. (7) Re-attach the top hinge screws, making sure the door is parallel to the freezer door. It took about 10 minutes to do all of the above. Best yet, I ordered the kit about 10am on a Monday, and the parts arrived, normal delivery, before noon the next day.PS- I used petroleum jelly to grease the hinge before replacing the door. The only tool I needed was a nutdriver.

Set up two saw horses to put door on. Unloaded door shelves. removed upper hinge, and lifted door from lower hinge, placed door on horses. changed lower hinge on refrigerator. put door back on lower hinge, and closed door. Put upper hinge back on. Reloaded door shelves. It took more time to Unload, and Load door shelves than to replace Hinge.

Pull out old pan,remove the vent cover from front and install it on the new pan, done.

removed door, replaced hinge, replaced door.

replace the lower door hinge assy. and closer cam as a set.Only used a 1/4" socket and ratchet.The process was very easy without any problems.

The Hinge Cam Riser came as ordered and arrived in 1 day! The original riser was clearly broken in half. After installing the new one on the door hinge and adjusting it several times, the door closed a little but still didn't close all the way. Finally, I re-installed all the door trays and filled them with the usual perishables, and the door closed perfectly! Apparently, the extra weigh on the door was needed to complete the job.