CSE9600ACE Maytag Cooktop - Instructions

Removed module replaced radiant element very easy repair.

This is a two module cook top That I have, 2 burners in each module. I took it apart take the damaged one out and replaced with the new one, put it back together and turn it on. Heeeyyyy it works. Thanks.(and I'm not an electrician)

Note that this model# is not my exact model#, I couldn't find it - but its almost identical to this newer version of my Maytag glasstop drop-in stovetop.

Also note that these instructions are VERY generic and not detailed, as most all stoves will be different in assembly.

Be advised that you are NOT getting the part you see in the picture. It is going to be a newer part that does the same thing. It's a lot smaller and has an offwhite top. It will STILL work, don't return it! The only difference is that the labels on the connections will be a little different - see the other post here on this page that shows how they differ and what to connect to what. Thanks to them I was able to complete this fix easily!

Close the breaker to the stove to ensure no electricity is running to the stove! Use a voltage tester to make extra sure no electricity is running through the cables, they are cheap at home depot!

Just disassemble your stovetop to get to the area that houses the switches. You will see the switch boxes underneath where your knobs go. Take a picture of all connections if you can so you remember where everything plugs in. You'll have about 3-6 cables connected to the switch depending on your stovetop. There are labels on the old switch (L1, L2, etc) at each electrical connector the cables attach to - probably on the top or bottom of the switch. Write down the connector label and what color wire its connected to. Do this for each connection.

If the old labels dont match your new labels, you have an older switch and need to check the other post on this page that someone posted showing how the old labels translate to the new labels.

Now reconnect everything back the same way you took them off and you are good to go!

Such a simple fix and you'll save hundreds.

simply took off smooth surface top flipped it upsde down on a towel. unbolted the entire burner assembly. matched connections with the new burner with limit switch. replaced smooth surface top plugged it in. no problems. extremely easy fix no repair charges.

Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall screws and turn Circuit breaker power back on. Done and Done

First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.

Exact fit, but read the instructions! Male connectors on element are labeled 1A 1B 2A 2C, very faintly etched in the ceramic. Even though the old and new elements look the same (and I took photos to aid installation), the connector locations are different -- 1A on the old element is where 2B on the new one is, etc. Used included extension wire for one that would not reach with the new configuration and everything works perfectly.

Very easy just followed manufacturers instructions.

Turned off power to cooktop and double checked
Lifted up entire cooktop and rested it on two pieces of wood that spanned gap underneath
Removed screws from around edges to free the metal framework that holds the cooktop in place-- this requires spinning the cooktop a bit to get access to the back.
Lifted metal framework off
Lifted glass from cooktop off
Checked configuration of power plug ins against new part and noted where they should go. There was a slight difference of how plugs were arranged, but it was easy to logic out.
Removed old burner unit and plugged in new one. Ensure that nothing was touching contacts.
Replaced the glass top onto cooktop
Put metal frame back in place and screwed in
Lifted entire cooktop, removed boards, and lowered back into place

Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.

This was a repair project on a Jenn-Air built-in stovetop, which I had trouble finding instructions on how to disassemble. My particular problem was that three of the four burners had no temperature control. They were either on high or off - no such thing as simmer. This is opposite the problem described as a normal indicator of burner control failure. Usually the burner just goes dead. The hardest part of the repair was accessing the metal plate the burner controls are mounted on. First, I flipped the circuit breaker to the stovetop. It will shock the cr@#p out of you if you don't (I have experience from poking around down there without turning the power off). First, I had to remove the two burner inserts. The left one lifted from the top and the right one lifted from the bottom. Don't lift them past about 30 degrees. They are meant to lift up just enough to clear the tray well and then slide out. After removing the burner inserts, I was able to unscrew the eight fasteners holding down the stovetop rim. After removing this, I pulled out the trays underneath the burner inserts and put them aside without unscrewing the ground wires that attach them to the stovetop chassis. After removing the two screws holding on the active burner indicator lights, I was able to pull it up and lay it aside. Then I had to unscrew the two large brackets under the cabinet to loosen up the stovetop chassis so I could lift the front of it up an inch from the cabinet to enable me to unscrew two small metal screws that attach the metal plate holding the burner controls. After removing the two screws holding each burner control to the metal plate, I could unplug each of the five wires from the old controllers and plug them into the new controllers, in turn, before reattaching the new controllers to the metal plate. After repeating this procedure two more times, I reversed the process to reassemble the stovetop and voila, turned on the power and it worked perfectly. The result; a happy wife. For today.

Removed the cook top from the counter. Removed the switch housing and then the switch. Found a match and ordered. Part came in 2 business days. Once I put together the housing and connected the wire housing the burner worked perfect. The downdraft fan remained on. Placed a call to Jenn Air service and was asked to disconnect the fan switch. There must be some memory in the solid state portion of the switch. After a few mins I replaced the fan switch and hooked up the wiring. All worked fine.

Unscrewed three screws securing the glass top. Lifted glass top and wedged it open. Took a picture of the current wiring. Removed old burner.Compared male contact points on new and old burner. Plugged new burner in appropriately. Note: The new burner is MUCH hotter than the old one.

I removed the glass top and replaced the switch unit successfully. Hardest part was removing the unit from the countertop and bracing the base with a 4x4.

I unscrewed the glass surface from the bottom portion where the element lays. I gently unplugs the element and plugged in the new element. Then screwed it back together.