CSB2121ARA Magic Chef Refrigerator - Instructions

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.

I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.

Just kept working on it.

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

removed old and instaslled new. biggest problem was getting to one of the screws.

I watched the repair video on the web site a couple of times just to get comfortable with what to expect. (i.e. pressing tabs on wiring harness to remove, placement of lift arm for removal and installation) These instructions were a big help...I had the removal, modifications and installation completed in less than 30 minutes. Ice cubes (without the extra icicles) in 1 hour...

The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!

I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.

Saw many photos on the Internet that looked like my ice maker, but they were different. I put in my Refrigerator model No. and found my exact replacement ice maker right away. I was a little cautious, because the new one didn't include the wiring harness, or the plastic cover. I took the chance and ordered it. Super fast delivery, a Day or 2 at most. Everything went smoothly, and after the new one was in, I crossed my fingers until the timer kicked in, and I started hearing ice cubes falling in the tray about 3 hours later. Success! I had been having problems with the ice maker almost from the beginning. Hopefully, the replacement will last longer. I will say that this Maytag Fridge. is the absolute worst kitchen appliance I've ever owned in my 47 years of house keeping! The defroster went in the freezer a couple of months after the Warranty ended, and it cost me $375.00 to have a Tech, come in to repair. I got away easy this time, buying the ice maker for $135.00 and being able to do the work myself.

Jim

There are 3 screws holding the icemaker in place. After removing the ice bucket, I removed the screws, then twisted the unit to gain access to the power plug. The plug is held in place by a plastic flap which is part of the connector. It has to be pushed down to remove the connector. The new unit went in perfectly and performed flawlessly for 3 days until the compressor blew out! After feeling some sense of accomplishment having fixed the icemaker, I learned that my neglecting to clean the vent grill in the front of the refrigerator had caused its demise. Don't forget to clean the dust out of the vents!

I disconnected power, turned off water supply, removed three hexhead screws, disconnected wiring harness plug, then reversed procedure. New icemaker seens to be a little slower in making cubes. However, the cubes are clean, perfect shape and THEY DO NOT CONTAIN ANY OF THE BLACK COATING AS THE OLD ICE MAKER CAUSED. THIS WAS A FAIRLY SIMPLE TASK.