All Installation Instructions for Whirlpool Dryer CS5000XSW0

Dryer electrically dead

Unplugged power cord. Removed rear panel screws and panel . Removed the two wires connected to part. Removed two screws holding part and replaced all components in reverse order.

Parts Used:

Dryer Disposable Thermal Fuse

Dale from Anderson, IN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

dryer wouldn't turn on

I removed the two screws on the top by the lint catcher. Then, per information from this website, I pried up the top. I reached down into the dryer and removed the two screws on the broken door switch and replaced it with the new part. I am a recently widowed, 55 year old and was thrilled to find good advice, information and instructions on your website!! Simple as could be!

Parts Used:

Dryer Door Switch Actuator

Kim from Northridge, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

door catch broke therefore dryer door would not close

just put the new part in the door---sooo easy! THANK YOU!

Parts Used:

Door Catch Kit

vernette from sprague, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Won't pump out the water

Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.

Parts Used:

Lid Switch

Victor from NORFOLK, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken dryer door catch

Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.

Parts Used:

Door Catch Kit

Kenneth from UPPR MARLBORO, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

broken door catch

I followed your short video and found it very easy to do

Parts Used:

Door Catch Kit

Susan from HUDSON, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

broken door catch

Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.

Parts Used:

Door Catch Kit

Frank from ENDICOTT, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer simply stopped running

I looked up the problem on Utube and saw a demo on what three items to check with a volt meter for continuity or resistence on either the start button, the door switch, or the thermal fuse. The first two checked out OK but the fuse was dead, no resistance or ohmns on the voltmeter. I had trouble locating it on my dryer as the Utube site said to pull the rear cabinet off when actually it was under the front panel below the dryer door sitting in an awkward position right on top of the dryer motor. I used 2 flat head screwdrivers to pry open the latches over the panel door that are located about 4 inches in from either end and then used a small right angle screwdriver with a flash light propped against the heating elements (after I removed the cover plate) to see with and to give me more room to loosen just two tiny screws that attached the fuse to the motor. Voila! It works better than before.

Parts Used:

Dryer Disposable Thermal Fuse

Linda from AMISSVILLE, VA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

dryer door wouldn't catch, catch was broken

took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......

Parts Used:

Door Catch Kit

Theodore from Tyler, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken door switch

I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.

Parts Used:

Dryer Door Switch Actuator

john from el paso, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Would not drain

Replaced lid switch, but problem still continued.

Parts Used:

Lid Switch

Robert from SANDWICH, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer would not start, timer had no power to it.

Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.

Parts Used:

Lid Switch

Billy from NEW BERN, NC
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Light stayed on, inside dryer. Dryer no workie

I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.

Parts Used:

Dryer Door Switch Actuator

Steven from New Richmond, WI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Dryer would not start. After first replacing a spare Dryer Thermal Fuse I had it tripped again due to overheating. I then ordered a replacement Dryer Thermal Fuse as well as a cycling thermostat after determining the thermostat was no longer regulating the dryer's temperature.

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

Parts Used: