CRT52 Husqvarna - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wheel bushings were bad
Removed old clip removed rim from tractor, removed grease fitting on rim, took hammer and screw driver knocked out old bushing turned rim over knocked out other bushing. Press in new bushings reinstalled grease fitting slide tire back on tractor, put retaining washers on then locking clip put on dust cover grease at grease fitting. Repeat other side.
Parts Used:
-
Anthony from OLIVEHILL, TN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
27 of 44 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken drive axle chain
removed engine, sheet metal, handle bars, and tines. Seperated transmission case and replaced broken chain. This is not difficult it's just time consuming. A tiller repair shop would charge about $400 to do this job. It cost me $40 for a chain and gasket, Both fit perfectly, great service. Thanks
Parts Used:
-
richard from MECHANICSVLLE, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original shield was damaged
-
Wayne from LAKEVILLE, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Deflector replacement
Removed pin and spring replaced old deflector with new deflector reinsert pin and spring
Parts Used:
-
Dennis from Marianna, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring on clutch cable broke
Remove L. wheel.
Remove guard shield.
Remove old cable.
Install new cable.
Adjust throw on cable.
Put all parts back and test
Remove guard shield.
Remove old cable.
Install new cable.
Adjust throw on cable.
Put all parts back and test
Parts Used:
-
David from SKANDIA, MI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken weld on right axle
Removed wheel (used strong magnet to catch the keeper)
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Removed axle assembly from its mounting tube
(used strong magnet again to prevent keeper lose)
Installed replacement axle (again with the magnet)
Lubricated with 90 SAE
Re-installed the wheel (used magnet again to hold the keeper.
Mowed the lawn.
Parts Used:
-
walter from EDINBURG, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced old belt
-
David from WINSTON SALEM, NC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set, Wrench set
4 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front wheels, too much end play
-
Frederick from BINGHAMTON, NY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
10 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!