CRE3870LBC Crosley Range - Instructions

Removed 2 screws, pulled out the panel, replaced the new panel and replaced the two screws. Less than 5 minutes.

Took out 6 screws from the back of the oven and removed metal cover. Unplug 2 connectors from the old control pad and removed mounting screws. Plugged in 2 connectors from the new panel, mount it and close up cover.

Used instruction video & replaced part.

Originally I had anticipated a major problem requiring the removal of the back of the range and perhaps the necessity of employing the services of a repairman ($$!). Fortunately I waited for the arrival of the replacement element, which, upon inspection, was not configured to go through to the back of the range. What a relief!

The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.

Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.

The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.

Pulled stove away from wall and unplug .Removed grates for better access. Unscewed element scews removed element & tested for continuity.there was none element is bad . Replaced with new one . Time about 20 minutes.

Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

I follow the video on your site

I looked up the problem on YouTube and it said it was the oven temperature probe was going out. So I ordered the probe and it was shipped out, received within two days. Took out a few screws on the back of the stove installed it, put it all back together and it’s working perfect.

The youtube video clearly described how to remove the back panel and how to replace the probe.
The repair took maybe 20 minutes to complete and 1/2 of that time was spent cleaning behind and underneath the range!
Range is working perfectly now!

Removed 4 screws on back cover removed 1 screw holding probe and unplugged the probe took it out and installed new probe.

in the bottom of the oven when I was looking to see what was going on. My husband did the repair just as the video described. I suspect this part honeycomb round maybe ceramic piece goes over where the heat is vented from the oven. Where do I get another one of these and how does it attach in the oven-under the burner. HELP I tried to look on the schematics and did not see anything. The repair went fine, except when we turned everything back on it did not work. Then my husband remembered he forgot to plug the new part IN. Once plugged in it is working fine. Thanks

Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

Very easy just had to pull the wire up that holds it secure.

Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.