CLL1101ADW Magic Chef Range - Instructions

The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Removing the oven door by partly opening it and pulling it up out of the hinge made access to the igniter much easier. Access to the igniter was easy. Just remove the baking shelves and lift out the bottom panel. I removed the two screws holding the old igniter. One screw was difficult to remove because of oxidation, and required some tinkering as the threads were stripped. But once the screws were removed, the igniter was easy to replace and connect to the gas controller with a simple plugin connection.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

My used stove had been dropped by the previous owner. While I could live with the minor scratches on one side the wooden shims holding up one corner were annoying. A new leveling leg was less than $2. I used a pair of needle nose pliers to straighten the mounting hole and screwed the new leg in. This used stove was originally $2000 but I bought it for $999. the new leg plus shipping was about $10. What a deal.

I opened the door partway to remove the door. Then I removed the bottom heat shield plate by pulling it towards me and lifting it up. I removed the two screws holding on the igniter, then with the the disconnect removed the old ignitor. I plugged in the new ignitor, replaced the screws, replaced the heat shield, replaced the oven door, and was done in ten minutes.

Replacing the vertical mount igniter was very simple. Remove 2 srews and one plug. I did pull out the oven to unplug te igniter. The process could not be easier.

1.) Remove door from hinges (open slightly and pull up). 2.) Remove racks. 3.) Remove oven floor to expose burner. 4.) Remove wing-nut and burner cover. 5.) Remove two ignitor mounting screws. 6.) Pull wires and connector through back wall. 7.) Connect new ignitor and mount to burner. 8.) Replace components in reverse order.

1)Completely removed racks, oven bottom and broiler drawer to access unit. 2)Shut off gas supply by by pulling horizontal lever on left side of safety valve forward to close valve. 3)With screwdriver, removed heat shield covering safety valve and connector from igniter. 4)With socket wrench, removed the two mounting screws on igniter. 5)Installed new igniter, connecting to safety valve. 6)Turned on gas supply by pushing horizontal lever to left of safety valve back to open valve (see step 2). Turned on oven to test. 7)Upon gas igniting, shut off oven and install oven components in reverse order.

removed oven door and shelves and lower pan and replaced igniter

took oven door off, took oven racks out, removed heat sheild, took 2 nuts off ignitor, removed ignitor, gently pulled ignitor wire out from back of oven, unclipped wire, clipped new ignitor to wire harness, replaced nuts to install new ignitor, replaced heat shield. replaced oven racks, replaced oven door, tested to make sure oven lite, took about 10 minutes!!

easy

Took off oven door. Took out oven racks. Took out bottom oven cover above igniter. Igniter is held in by 2 screws,took them out with a small socket. Went to back of stove and unhooked white plug in - (part of igniter) Thats it. About as easy as it gets. Just reversed the process putting in the new one. Took about 25 minutes. It would have taken less time but I had a problem with one of the screws. Probably from the heat. The oven is 9 years old.

After reading about my problem, I determined it was the igniter. I immediately ordered one. It came two days later. I took the bottom drawer out and removed the shield. To get to the plug wires, I unplugged the old igniter. I used my power nut driver to take off two threaded screws so igniter could be removed. I then pulled the old igniter out. Plugged new one in and reversed process to install new one. I installed it when I got home from work in less than 30 minutes. all is well. We were looking at buying a new stove for $700.00. I fixed it for less than $60.00. Thanks

removed oven door, removed all shelving....unplugged the electrical cord........unsrewed the igniter(2 screws)removed some of the insulation on back of oven that was covering the wire and plug......disconnected the wire plug...........reversed the process and 15 minutes later I was done............the oven works great.......the new igniter arrived 2 days after I ordered it. thanks

I called the yellow pages repair man and he quoted me $450 to replace the igniter. I did it myself for $63 and it took 10 minuet's. I'm gonna get a T shirt that says "Mr Fix It" Next is the refrigerator door gaskets! Someone from part select had mentioned that to take the door off the oven you "just open the door a little and lift it off". that was a helpful hint because I would have been looking for screws for half a day!