CGC355DXD Gibson Range - Instructions

The repair was simple - I first needed to test the original igniter with a circuit tester. Once I determined that the part was bad, I simply removed it and replaced it with a new one from Partselect. It was a matter of simply unplugging a few wires and splicing the new igniter in with wirenuts. Fairly simple.

CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.

First i removed the broiler door and then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and cut the two wires. I strip the ends ,connected the new unit with ceramic nuts that was provided an reconnected the unit. all was done in less than 30 min. EASY!!! plug the stove back in and WORKED PERFECTLY. note i receive the unit the same day it shipped....WOW

Removed racks,oven bottom(2 screws) and heat deflecter. Slide heat sleeves 10 inches away from old igniter. Cut wires one inch longer than the length of the heat sleeves, from the old igniter. Cut the new wires to match old wire length. Replace old igniter. Slide sleeves up to new igniter. Wire nut ends-done deal. It was hard working over the oven door,but I am old. Good luck

first i removed the bottom of the oven [inside the oven] ,the part was right there,i removed 2 screws and unpluged the wires,then i cut the wire ends off the old part and used the wirenuts that came with the new one to hook them to the new part,then put it back in place,put the screws back in put the bottom back in and was done

had to remove burner bolts holding igniter were stripped cut two wires replaced igniter using two self tapping screws put wires together using wirenuts Honey making cookies right now thanks already told friends about you

Removed lower drawer of oven and base panel of oven. Unplugged stove from outlet. Removed old igniter w/ nut driver (two screws). Disconnected wires (blade connectors) from stove base. Disconnected two-pole plug from oven after removing protective cover in corner.

Install new igniter. You will need to cut existing wires from old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit.
Directions are also provided with the new igniter.

1 - I unplugged the oven/ stove connection.
2 - Removed 2 screws and lifted it out the floor of the oven.
3 - Removed the nut holding down the flame guard and lifted it out.
4 - Removed 2 screes that held igniter in place.
5 - cut the wires for igniter.
6 - Stripped new wires with the nuts connector.
7 - Installed new igniter with 2 screws.
8 - Put it all back together step 3 & 2.
9 - Plugged in the oven/stove connection.
10 - Turn on the oven and works perfectly.
11 - My wife and daughter happy and ready to bake.

I removed the oven floor and subfloor. I detached the old ignighter leaving the wires still attached. I then attached the new ignighter and fed each of the two new wires down through the bottom of the oven floor following the same path of the old wires which were still attached. I attached the new wires one at a time to make sure I connected them to the right place. Then, I pulled out the old igniter. I then attached the oven floors and turned the oven on which now works. The tough part is pulling the oven out from the wall to disconnect the power and turn off the gas. I did not remove the oven door.

As the previous people stated on similar repairs;
I took the new drip pans out of the box,removed the old grate burners and the old rusty drip pans; then, simply set the new pans in place and replaced the existing grates. This whole process took less than 10 minutes.

Unplugged the appl. I removed the bottom of the oven. Disconnected the two wires. Removed two screws that hold the element in place. Replaced it. And put everything back together. Since this element goes bad about every year an a half, I keep one on hand all the time.

I found your website fast and easy. I needed replacement drip pans fast, ordered them on-line, and received them within 3 days of ordering. Your parts were the best deal, the least shipping charges, and the picture and description on your website was the best. Thanks.

Opened the box, took out the drip pans and the put them on the stove. Wow -- even a techno-challenged person like myself could do this! I ordered these on a Tues. at 2:00 p.m. and received them on Wednesday -- that is a first so thanks for the fast service and they look great! Was non-existent to find them at local appliance stores in the area so thank you for having them.

Removed the broiler compartment door by depressing the slide stops inward and pulling the door off. Turned off the breaker to the oven. Used a nut driver to remove the old ignitor ( 2 screws ). Cut the wires off the old ignitor close to the porclin. Measured the new ignitor wires to match up with the old ignitor wires and cut them. Stripped 3/8 " off ends of newely cut wires of the ignitor and used the supplied wire nuts to secure them together. Replaced the new ignitor with the 2 screws. Turned on the oven and a cooking I went.

First unplugged the oven from the wall and then I removed the bottom floor of the oven by removing the two screws at the back. Then I removed the heat shield over the burner by remove the two screws at the front of the oven and removed the nut in the middle of the heat shield that was hold the shield to the burner. I removed the two screws on the flat oven igniter and cut the two wires on the igniter and pulled the two wires through the open in the bottom oven from the drawer opening. Mounted the new igniter and feed the two wire from the igniter through the open in the bottom of the oven, Stripped the two wires that I cut from the oven, twisted the new wires to the old, and put the wire nuts on. Last I put everything back together and baked dinner. Took ten about minutes and saved a thousand dollars because I was going to buy a new oven. Thanks, Partselect.