CFHT1814LZ4 Frigidaire Refrigerator - Instructions

After watching numerous YouTube videos I realized that my problem was either the timer or the thermostat. I purchased both for above $70 total and decided it was worth the gamble to self- repair it instead of buying a new refrigerator for $700 plus taxes and delivery charges. The videos were right on with excellent directions for replacing these 2 products. Only has one problem… the shrink wrap that came with the thermostat is very thick and will NOT shrink with a hairdryer. I hade to run to ACE Hardware to buy a heat gun and more shrink wrap

It was extremely easy. I opened door, unscrewed the two (2) screws at the top of the door handle with a phillips screw driver. Once screws were out I rotated the handle to the left and unhooked it from the mounting block. The new handle was already equipped with a mounting block. I attached the new handles mounting block to the door and rotated the handle up and positioned the holes to the holes on the door. I used the same 2 screws from the old handle and tightened them into the handle and door. That was it. Very easy.

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

You tube is my best friend for DIY repair. I supported the door with wood blocks, removed the bottom bracket and was able to slide the refrigerator door down and out without removing the freezer door. Replaced both hinge bearings and door stop and washer on bottom hinge and slid the door back into place. Door is very light when empty. Fast and easy, door opens and closes smoothly and no problem with condensation anymore.

Very simple. Remove the 2 top screws on the door, slide the lower part of the handel on to the lower screw on door .,swing the handle up to the top of he door and attach with the 2 original screws. DONE

Since the glass was broken and gone I just had to slide the new glass on top of the crispers. This was not really a repair, just an exchange of new for the old.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

I take 2 crew on front of the fridge take the cover and fan out replaced the part and put everything back it’s a easy job thanks guys for the parts from Orlando fl

I simply loosened the screws holding the refrigerator door handle and then slid the bottom portion of the handle off from the screw holding it in place. The bottom portion of the handle did not exactly marry-up with door, showing a very small gap. I attributed this to the age of the appliance.

Simply slide the new glass insert in!

Open door and use a screwdriver to remove screws. SAVE the screws because the new handles do not come with screws. Rotate broken handle to the left and slide the handle to the left which should slide the handle off of the screw protruding from fridge door. To install new handle, repeat this process in reverse. Rotate new handle up and screw onto fridge door.

The repair was quick and easy. I simply removed the old/cracked door shelf retainer bars and snapped the new ones into place.

Unplug, remove 2 screws off back panel inside the freezer. Cut wires on old one and crimped in new one. Light to melt the shrink wrap that came with it. Pretty easy.

Simple repair and less than 30 minutes.
But the video you had was taken down which showed you need to wind the timer. I called and was promptly sent another video, thanks Ashley !

Unfortunately the second video did not mention that you have to wind the timer, like the first video did. Turn clockwise till you hear 2 clicks.

All good. 20 year old fridge chugging along.

It was easy to remove the broken handle and install the new on. Only thing needed was a screw driver.