CFGF337GSA Frigidaire Range - Instructions

Open the door and slide in the new rack.

Easy installation using a nut driver and a Phillip screwdriver.plug in harness connector and done.

Watched a half dozen You Tube Videos before I saw the Exact one-Submitted by a Woman-Super Easy-Had the Exact Part from this site!

Removed the metal cover on the back of the range by unscrewing the square-drive screws around the perimeter, left the center screw until the end to make it easier to hold for removal.

The control unit was held in with 4 Philips head screws, and connected by a single wire-to-board connector. Unplugged the connector and removed the screws and the control unit came right out.

The replacement unit doesn't come with a face plate, so I used a razor blade to carefully remove it from my old unit. The adhesive that held it on was still sticky so I was able to easily attach it to the new unit.

Then I just put everything back together in reverse order. One of the easiest appliance prepares I've done.

moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.

Took out old screws and replaced with new

My daughter did the installation and it was quick. She had no problem, and it's working great. She love it. She just use a philp screwdriver to take off the bolt then unplug the control adaptor. From the back then plug the new one in and that's it. Easy as 123

YouTube video I used was for a newer version of the same model stove. Door did not have latches to remove it. It was fairly easy getting to the old igniter but a bit of a struggle getting to unplug it, as the connector was behind a small metal shield in the bottom left corner of the oven. Because I couldn’t remove the oven door, it made it more difficult to undo the screw holding it in. I finally did, and from that point it went smoothly. I was worried that I was going to access it from the back, but I didn’t need to. I installed the new one, turned gas back on, moved the stove back to position, and turned on the oven. Very happy to have succeeded, adding a few more years to the stove and saving money for the installation of the igniter.

The electric was the next step it worked.

replaced it

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.

PartsSelect.com saved me lots of $$$$$. I have had appliance repairers come and view the stove and tell me I needed so much work. I paid them and the stove still wasn't fixed. I figured out the problem and found PartsSelect.com = savior!

Timer was bad. Removed the four screws on the rear panel, and then the four screws holding the timer in place. I let the old one dangle by the wires until the new one was in place, then just switched the wires one at a time. There is one set that has a plastic connector, and you need a small flat screwdriver to depress the locking tab on the top of the connector to release it. Be sure and order a new face plate as the old one will not come off without tearing. Re-install rear cover and your done.

Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair