CFEF3019MSD Frigidaire Range - Instructions

At the Frigidaire parts website, I found the parts and saw that there are videos that show how to replace the burner controls. In brief:
1) Slide the range/oven out so you can get to the back of the control hood.
2) There are three screws that hold the cover in place (the video showed four).
2a) The video also suggests using a #1 square bit. I found that there was indeed a square hole in the caps of the screws, but they also had a hex head that a 1/4" hex nut driver fits. So I used that.
2b) Be careful taking out the last (top center) screw. When it comes free, the cover can drop and bruise or cut your foot or the floor. Having a helper is worth it!
3) The switch for the larger elements has a red dot on front and back. Match it with the one in place that has a red dot. The switch for the small element doesn't have a dot.
3a) Holding a new switch in your hand, remove one wire at a time from the switch in the control hood and put it in the same place on the new switch. I found that for my stove, there was a fixture holding two wires and another holding three wires. This made it impossible to put the wires on wrong.
3b) When all wires have been transferred, pull off the control knob in front and unscrew the two screws that hold the old switch in place. Take out the old switch and replace it with the new switch.
3c) Use the two screws to attach the new switch in its place and replace the control knob.
4) Repeat for as many switches as you purchased. I did all four.
5) Replace the cover.
6) Slide the range back into place.

I found black deposits on all the switches, that must have come from a contactor inside, so I was glad I replaced them all.

Another tip: while the unit is out, clean off the sides and back that you couldn't get to while it was in place. For us, this took as long or longer than the steps above for replacing the switches.

First unplug the stove before staring any of this task. loosen and remove three cross tip screws at the upper front of the stove top. You will need a piece of 1x3 wood about 1 1/2 feet long to hold the stove top up (sets at an angle upwards to the front). Loosen remove the bracket holding the burner you wish to replace. Disconnect the electrical wires connected to the burner. The burner is held in place with bracket clamps, remove the clamps from the oven bracket holding it. The burner will have a series if numbers in the back side, remove the brackets one at a time and reinstall on the same number on the new burner. do this to all 3 or four brackets. Install the new burner, install the bracket holding the burner, reconnect the wires. remove the wood brace and all tools. lay the stove top back down on the stove. plug the stove in and test the burner to make sure it works. turn off the burner and install the screws hold the stove to in place. Ta-Da your done. Also you tube has movie shots to give you a much better picture of what I just wrote about...

Went very well and it works!

Replaced the dual element switch and that fixed it up

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

My husband followed the video instructions and it was easy to fix.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

Took out 2 screws, removed panel.
When you put the panel in don’t push it tight to the front or the screws won’t align. Just place in gently and the screws will align

removed the old burner and put the new one in it's place.

made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.