CEX210VL0 Whirlpool Cooktop - Instructions

Shut off power to the stove.
I removed the screw that held the block in place. Then I lifted the top of the rage to get to the wires. I cut the wires from the old block and stripped back the insulation. Next I put the heat shrinking sleeve on. I attached the new block with the wire nuts, pulled the sleeve down and used a hair dryer to shrink them. Then you just hook it back on screw it in and your done.

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan

This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.

Pulled out the old burners and put in the new ones.

Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts together with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.

I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...

Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube over the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.

First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They work very well now.

lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly

I ordered the 2 burners that were not working. When I got the burners, I discovered that one of the burners was still working and the wiring under that on had burned out. So I ordered the little box kit and repaired it. I only needed to strip wires and twist together and replace the small box. Now all are working and I am cooking with all four burners again. All for about $50.

Cut power. Removed four attaching screws and raised stove top. Cut two wires of existing burner plug. Used existing plug to select correct plug configuration from parts in kit. Attached new plug and wires to wiring harness using connectors and heat-shrink tubing supplied with kit. Used hair dryer to shrink tubing on connectors. Closed up stove. Restored power. Burner now functional.

Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!

The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the connectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked!
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.

pulled out old burner and pushed in new burner.
No tools needed.

Simply removed new burner from box and plugged it in! Very pleased with 3 day speedy delivery. Confident my 32 year old cooktop will continue to give many more years of service with any parts needed from PartSelect.