All Installation Instructions for Crosley Range CEW4D59CO

The broiler element made a loud noise.I immediately turned the overn off. It kinda acared me.

My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you can find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.

Parts Used:

Broil Element (15 Inch long x 12 Inch wide)

Ann from Schertz, TX
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Not heating

Was easy cut the wires of as told to do wire nut the ends together and put back together and tested and worked great. Done

Parts Used:

Surface Burner Receptacle Kit

Darwin from wisconsin rapids, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Light bulb failure

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Parts Used:

Light Bulb - 40W

Grant from Alexandria, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner element stopped working

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

Parts Used:

Surface Burner Receptacle Kit

Robert from Lodi, CA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

Drip bowls were all rusted.

Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Robin from Seneca, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

The drip pans needed replacing.

Put in the new drip pan -- which are really nice shiny ones.

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Alison from Carnation, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Dirty drip bowls

Just remove old bowls from range top and put new ones. That is all ... just super simple! :)

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Paul from Carnegie, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

I needed to replace to two 8* drip bowls on the kitchen range

(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.

Parts Used:

Chrome Drip Bowl - 8 inch

Dallas from Arlington, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Stove needed new bowls

Just dropped in

Parts Used:

Chrome Drip Bowl - 8 inch

Drip Bowl - 6 Inch

Karen from Kettering, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Old dirty drip pans

Removed heating element, installed new drip pan, replaced heating element. Was amazed at fast delivery - ordered in afternoon, arrived fed ex next morning!

Parts Used:

Chrome Drip Bowl - 8 inch

gizella from mays landing, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Burner no longer connected with electric power source

I had determined that the the burner itself was no longer capable of connecting because when I removed another burner and inserted it, it worked just fine. Also, the defective burner had not worked when inserted into another outlet. I was delighted to be able to purchase a replacement so quickly and easily on my own, without having to call a repair person or seek a retail outlet.

Parts Used:

Standard Y-Frame Range Surface Burner

Barbara from Pacific Palisades, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

The surface burner element burned out on my 20 year old Jenn Air electric stove.

It was so easy to order a new one from your company. And it arrived in less than a week! I slipped it into the electric outlet and it worked perfectly. THANKS. Wanda Major

Parts Used:

Surface Burner Element - 8 Inch

Wanda from Riverton, WY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

one pole of the socket corroded to nothing

Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.

Parts Used:

Surface Burner Receptacle Kit

martien from williamstown, MA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Oven would not heat up properly to set temperature

The element appeared to have been damaged. I replaced the element with ease. However, I still have the same problem. The oven does not heat up to the set temperature. Information from the part select website is that it is more likely the long oven sensor. I ordered one and will provide the results after I have this sensor replaced with a new one.

Parts Used: