CEC2S5WSAA Gibson Range - Instructions

Removed the racks first. Then removed the two screws that held the element in place.
I then pulled the element out about three inches
exposing the connecting wires.Each wire has a female slide type connector just disconect each one and then connected the new element .
Attach new element by reptacing the two screws.

Really easy--unscrew screws, pull element out, unclip wire connection. Re-clip to new burner, put back in--done. Saved a $100 tech trip PLUS double mark up on part!

First my husband removed the two screws that held the heating element into place. I had tried it with pliers which didn't work well. But with the proper socket the screws came loose easily. He pulled the heating element out a few inches and detached the wires. He then slipped the wire over the new heating element and screwed the new element into place. Now we can bake again. Very easy and we received the part quickly.

Removed back cover, unhooked wires, unscrewed and removed bad baking element. Reverse order to install. Less than 15 min. repair job.

First unplugged the stove, then removed the screws holding the element in place. Next I pulled the element out until the wires were visible and unplugged them. After removing the old element, I plugged the new one in and positioned it with the screws. Plug the stove back in and done.

Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

pulled the element out and found it burn the connectins on one side. so i had to pull the stove and open the back to get to wiring. put a new connecter on. then connected the new element. closed the back.

the repair itself went smoothly. the clips that the new part connected to were old and slack. the clip came undone and had to pull the stove out to get to part from the back. i squeezed the clip together to make it stay on the new part and it held. the oven is heating well now.

Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.

Plug the new element into the space on stove

Cut the old block off tied new wires to hot wires . That easy!

First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!

Repair was simple. Unplugged stove, removed a plate from back of stove. Disconnected wiring. Removed screws from inside oven, removed old element, installed new element. Replaced screws, hooked up wiring, replaced back plate, plugged it in, used it that night.
Thanks for sending the right part the first time and getting it shipped so quickly.

First shut power to oven off, removed the oven door and oven racks. Removed the 2 screws from the back of the oven holding the element in place. Slowley pulled the element out and removed the wires, pulled off with my fingers. Replaced the old with the new in the reverse order. Saving the Wife a pile of money.

Thank You,
Jerry R