All Installation Instructions for General Electric Range CCGS990SET1SS

Oven meat probe broken

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Parts Used:

Meat Probe Thermistor

robert from FAIRFIELD, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Replace temp sensor in gas range

Part came as ordered. Hardest part was fitting plastic wiring harness through the hole with 2 layers of steel with insulation in between. Used electrical tape to stiffen the end about an inch or 2 back from harness. Job done, problem solved

Parts Used:

Range Oven Temperature Sensor

Ron from PAINESVILLE, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

shortage in wiring cause the housing to burn out

Replaced new light housing.
Thanks to you guys for the prompt response

Parts Used:

Oven Light Housing

fred from PALM COAST, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

flame was inconsistent. too much air.

replaced old with new.

Parts Used:

Vision Burner - Extra Large

Raymond J. from EASTPORT, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Water would fill washing drum when off

Remove and replaced water valve, seems to have fixed the problem

Parts Used:

Knob Dial Skirt

joseph from SECAUCUS, NJ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven sensor not working

Very very simple repair!!!!! Works great!!

Parts Used:

Range Oven Temperature Sensor

Mary from TUCSON, AZ
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

stripped control knob

remove and replace the same .

Parts Used:

Burner Knob

michael from milford, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Gas Oven will not light

I was disappointed with this parts recommendation..neither part solved the problem, a first with partselect. The Range Oven sensor change out was easy and straight forward once the back lower panel was removed. The SPARK MODULE was time consuming..the module is located and accessible only by removing the range top. Having gas burners requires unscrewing all the burners before tipping up the top and removing it, then removing the guard over the Module is next..it's a project, sure wish it worked when I was done!..turned out to be the oven glow bar....

Parts Used:

Spark Module

Range Oven Temperature Sensor

Daniel from NASHVILLE, TN
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Part does not look like the part that needs to be replaced

I have no clue what wire goes where because there is no thing to refer to or instructions of any kind . I have not been able to install the part.

Parts Used:

Spark Module

P from FULLERTON, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

To Replace Gas And Burner Parts In Section 4

Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instructions to complete

Parts Used:

Top Burner Spark Electrode

John from Long Beach, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Wrench set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Deflector oven/gas flame deflector replaced due to hole melted from glowbar igniter

Removed oven convection fan cover for more room to remove/replace lower oven bottom. Deflector is attached underneath oven bottom and you will need new self tapping sheet metal screws to replace old ones. My deflector actually had hole melted in it from glowbar igniter directly underneath it. Glowbar remains white hot until selected oven temp is reached...poorly designed.

Parts Used:

DEFLECTOR OVEN

Barry from Coventry, RI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Broken Probe Sensor

Replaced it

Parts Used:

Meat Probe Thermistor

Michael from Tucson, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

the original knobs were plastic and cheap and cracked within a year

pull off old ones, which wasn't hard because they were cracked. push new ones in. Some were a little harder than others but all went in with a little push.

Parts Used:

Burner Knob