CC1EF Amana - Overview
Models starting with CC1EF
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Range Surface Burner Plug-In Block Kit
PartSelect #: PS340571
Manufacturer #: 330031
The surface burner plug-in block kit features a newer-style terminal block. This kit is designed for use with ranges and cooktops. This terminal block is how the coil element on your stove connects to...
$16.07
In Stock
Surface Burner - 8 Inch - 2600W
PartSelect #: PS11743367
Manufacturer #: WP660533
The surface burner or element on your range provides the heat that you cook with. If your element will not heat, you may need to replace the surface burner. This surface burner is 8 inches in diameter...
$33.69
In Stock
6 Inch Drip Bowl - Black
PartSelect #: PS2377817
Manufacturer #: W10290353RW
Sold individually.
$20.37
In Stock
8 Inch Drip Bowl - Black
PartSelect #: PS11752111
Manufacturer #: WPW10290350
This black porcelain drip bowl with a hole in the bottom is intended for use with some electric ranges and cooktops. This drip bowl measures 10 inches in diameter at its widest point. The purpose of t...
$16.07
In Stock
Surface Element - 6 Inch
PartSelect #: PS11751368
Manufacturer #: WPW10259868
Get your cooktop working like new with this 6-inch coil burner. It heats up with 1500 watts of power—great for boiling, simmering, or everyday cooking. Easy to install with looped ends that connect qu...
$89.21
In Stock
Surface Burner Element - 8 Inch
PartSelect #: PS11740903
Manufacturer #: WP3191454
This surface burner element is a genuine OEM replacement part for your kitchen appliances. It measures 8inches in diameter with a wattage of 2100W. You will need to replace the element if you notice t...
$95.15
In Stock
Range Installation Screw
PartSelect #: PS11741612
Manufacturer #: WP3400882
This screw is sold individually.
$7.47
In Stock
Ground Contact Spade
PartSelect #: PS1743150
Manufacturer #: Y0052041
Sold individually. This spade is used for either a ground contact or a power contact.
No Longer Available
Surface Element Kit
PartSelect #: PS373085
Manufacturer #: 4392061
This kit includes two 8" elements, two 6" elements, four receptacles and any remaining hardware needed for installation.
$79.82
In Stock
Common Symptoms of models starting with CC1EF
[Viewing 2 of 2]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
8 inch burner wouldn't come on. Wires shorted out
One screw holds the block onto the stove top. Had to clean out fitting for phillips screwdriver or screw would have stripped because it was old with lots of buildup. Even cleaned out, this screw required great force with phillips screwdriver to keep from stripping. Caution! If you strip it, you'll have to drill it out! The rest was a snap
... Read more
. Cut the old wires leading to the old block (not too close to where wires disappear into back of stove, though!). Strip insulation off both wires and attach with the connectors that came in the kit. Then push the wires into the block, and finally, attach the block back to the stove top (new screw is supplied). Restore power and everything should be fine. One problem: Roper/Whirlpool built their appliance in such a way that when the connector block shorts out, it usually takes the infinite switch with it. So I ended up having to go back and purchase that switch as well (which just so happens to cost twice to three times as much!). If you put it all back together and it still doesn't work, that's probably what happened, so go ahead and remove the knob panel and check that switch (it's right behind the control knobs on the front). You will probably find a burned connector at the back top left or the switch. Don't forget to write down which wire goes where (or just take a picture of it).
Read less
Parts Used:
-
Jonathan from Lilburn, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
61 of 72 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One burner didn't work all the time the other would go red hot
I unplugged the stove from the outlet, then removed the two burners I was going to be working on and the drip pans. Then I raised the top part of the stove and removed the screws holding the plug-in blocks to the stove. Then I cut the two wires going to the old plug-in block and stripped the wires back to match the new wire parts. Then I
... Read more
placed the sleeves over the new wires, then I placed the new wire beside the wire I stripped on the stove and screw on the wire cap making sure it was tight. I repeated this three more times, once I had all four wires connected I then placed the sleeves over the connections and heated them up until they were formed around the connection. Once I had all the connections done I placed one wire at a time into the plug-in block until it locked into place ( I looked at my old plug-in blocks first to make sure I placed the new wires in the correct way ).I then used the metal mounting bracket that matched my old ones and snapped the correct one onto each plug-in block. Before mounting them onto the stove I compared them to my old ones to make sure they were correct. Then I used the new screws to mount them to the stove. I took a second look at everything I had done before closing the top cover of my stove. After lowering the cover back into place I put both the drip covers in place and then installed the burners.I then plugged the stove back into the outlet and tried the burners. This was very simple and the video on the web site shows this very well which made my job very simple.
Read less
Parts Used:
-
Phillip from Pekin, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
15 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electric burners where consistently intermittently working right. Sometimes they would work on High but not able to adjust to low heat. Sometimes they would just not want to come on at all. Occasionally there was a spark at the connection. If I jiggled the element just right it may or may not wo
Thought we was going to have to replace the range all together, due to most parts not being available for this model anymore. Since this is an expensive model, we did not look forward to having to replace it. So I thought just by chance I would check to see if anyone had parts to help in repairing it. Part Select did happen to have the
... Read more
Surface Plug-in block kit that was needed. After going at least a year with this problem, I am sooooo happy to say it is finally fixed and working great! Thanks much Parts Select.
Read less
Parts Used:
-
JOAN from Pickford, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!