CAW8350EW1 Crosley Washer - Overview
Sections of the CAW8350EW1
[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Washer Drive Pulley
PartSelect #: PS10057144
Manufacturer #: W10721967
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging th...
$38.06
In Stock
Washer Drive Belt
PartSelect #: PS11747978
Manufacturer #: WPW10006384
This genuine OEM drive belt is designed to transfer power from the motor to the drum in select Whirlpool, Maytag, Kenmore, and other compatible washing machines. Operating at 115 volts and 60 Hz, the ...
$28.79
In Stock
Dryer Screw
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.30
In Stock
Washing Machine Door Lock Assembly
PartSelect #: PS12704713
Manufacturer #: W11307244
This is lid lock designed for use within various washing machines. This lid lock, also known as a latch assembly, is used to secure the lid of your washing machine during the washing cycle. If your wa...
$100.39
In Stock
Water Inlet Valve
PartSelect #: PS12349267
Manufacturer #: W11210459
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work glove...
$65.23
In Stock
Suspension Rod Kit
PartSelect #: PS11703288
Manufacturer #: W10780045
This suspension rod kit includes four rods designed to stabilize the wash tub in compatible top-load washing machines. By minimizing vibrations and excessive movement during wash and spin cycles, thes...
$74.41
In Stock
Washer Washer
PartSelect #: PS11742027
Manufacturer #: WP3949550
This part goes on the agitator retaining bolt.
$12.55
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$11.50
In Stock
Washer D-Shaped Knob Insert
PartSelect #: PS11746209
Manufacturer #: WP8536939
This insert is sold individually. Knob not included. Knob is sold separately.
$9.40
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$9.40
In Stock
Affresh Washing Machine Cleaner - 3 pack
PartSelect #: PS1960673
Manufacturer #: W10135699
Having trouble with your freezer?s efficiency? Your GE Freezer Door Gasket might be the solution you?re looking for. This is an official replacement part designed to perfectly seal your freezer door. ...
$19.89
Special Order
Lid Hinge Mounting Screw
PartSelect #: PS11748588
Manufacturer #: WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$7.30
In Stock
Questions And Answers for CAW8350EW1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Shamar
November 25, 2023
My washing machine will fill up with water, then makes loud noise intermittently when attempting to wash.
For model number CAW8350EW1
Hello Shamar, thank you for the question. According to our research, we would recommend checking the washer drive pulley, part number PS10057144, to fix the issue. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Related Parts:
Washer Drive Pulley
$38.06
In Stock
Flavio
May 30, 2024
When i try to make anything the machine just doesn’t work, i push the start button and it flash and then it just start making “bip,bip “ every 3 seconds and doesn’t makes nothing i dont know what’s happening?
For model number CAW8350EW1
Hi Flavio, thank you for reaching out. We would suggest checking the control board, part number PS12347257. It manages the washer's functions such as filling, washing, draining and spinning. You may need to replace it to fix the issue. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Related Parts:
CNTRL-ELEC
$289.59
Special Order
Jane
July 21, 2021
The lock lid is stuck on, locking the lid, holding the push/start for 3 seconds will not unlucky the lid
I don’t know how to open the lid. I don’t know if I would force it open which will break the lock if it will start again and run its full cycle if the lid isn’t locked
For model number CAW8350EW1
Hello Jane, Thank you for the question. You will need to open the Cabinet of the appliance to access the lock to remove it to release the Lid. We hope this helps!
Was this helpful?
Thank you for voting!
Jim
February 17, 2023
Washing machine stops before completing cycle and indicator light goes back to wash. Is this a bad control board?
For model number CAW8350EW1
Hello Jim, thank you for reaching out. Based on our research, you need to check the following parts to fix this issue: selector switch, part number PS11752020, drive motor, part number PS11757089, drive belt, part number PS11747978, and the control board, part number PS12347257. If any of these parts are found to be defective, replace them. We hope this sorts out your problem!
Was this helpful?
Thank you for voting!
Related Parts:
Washer Drive Belt
$28.79
In Stock
Selector Switch
$75.05
In Stock
Drive Motor
$165.78
In Stock
CNTRL-ELEC
$289.59
Special Order
- < Prev
- 1
- Next >
Common Symptoms of the CAW8350EW1
[Viewing 16 of 16]Will not agitate
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Cycle Not Advancing
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Draining Issues
Fixed by
these parts
these parts
Show All
Timer Not Working
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Noise on bottom of Washer louder as time went on. 1 1/2 years
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read more
and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
Read less
Parts Used:
-
Jerry from WALLA WALLA, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set
92 of 124 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noise, grinding sounds. Wash tub stopped turning but motor and cycles kept functioning. Process of elimination, must be the clutch assembly.
Easy, just followed the repair video. Recommend also ordering the drive belt. Bought one locally during my repair.
Parts Used:
-
David from BLOOMINGTON, IN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
65 of 98 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water would not fill the washer except for 4 inches.
Once we put in the new Water Inlet Valve, the auto sensor works now and I can wash any size load
Parts Used:
-
Patricia from MURPHYSBORO, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
38 of 51 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!