C3842XRW Magic Chef Range - Instructions

Old surface element was removed simply by pulling it out of the electrical contacts. The, the new one was inserted.

pulled breaker,removed oven door,removed 2 screws,pulled bake element out 3 inches,pulled connections off,pushed connectors on new element,pushed new element back and replaced screws,replaced oven door ,pushed breaker back and turned on oven and let it heat up to 350 degrees.
Total time 10 minutes,even a caveman could do it.

Turn Off the BREAKER!!!
Unplug the stove/oven
Opened the oven door
Unscrewed the baking element for the oven
Pulled the old element out about 3"
Disconnected the wire clip on both sides
Plugged the element into the clips
Screwed element back into place
Plugged oven in ,turned on breaker
PRESTO DONE

My husband has moved out of state for his job. I am left here with the children until the house sells. This is the first time I have ever had to do any oven repair. I had excellent and fast service - my part came right away. I took out the 2 screws holding the element in place, pulled the element out, disconnected the old element, connected the new one, pushed it back in, and replaced the screws. No problem at all. I was a little nervous turning it all back on, but it is working perfectly!

Turned off power, removed 2 screws, un-hooked the connections, them put in the new element in reverse order.

First I turned off power to the range at the fuse box (very important-The last time I didn't do this and ended up paying a repairman $150.00 to replace the damaged connectors). I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then connected the new element, pushed the element back in and replaced the screws. Turned the power back on and tested the element. The whole job took about 30 minutes because I had trouble disconnecting the old element. I used the flat end of the scrapper to push against the connector while I pulled the element out. Normally it would take only about 15 minutes.

I let my husband to the work...But it was very easy. I could have done it! He removed the screws, pulled the wires off previous element. Reattached the wires to the new element and screwed the ends back in place.

First throw the breaker on the stove. Remove two screws in back of oven then slowly pull out loosen the wire attachements ......got new part in 2 days just as simple reverse the removal directions.,,,I am over 60 female and it was simple.

The burner wouldn't work. I just plugged in the new one and all was done.

Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk

Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!

Watched the video that was available and followed the instructions. Unplugged the stove first,removed the old element, and put the new one in. Video was very helpful and the installation was very easy. Was done in about 10 minutes.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Removed old element, pluged in new element.

First I removed the two screws that hold the element in place. I then pulled the element out about three inches and disconnected the two wires, being careful not to pull the plugs off. I then inserted the new element and reattached holders. It was very easy and took less than five minutes. The part arrived amazingly quickly. The stove works great now.