C31315VBV Crosley Range - Instructions

Note the position of the electrode on the side of the old burner cap. Turn the old burner cap one-eighth turn counter-clockwise to loosen and remove it. Raise the burner cap and disconnect the push-on connector wires from the ground and electrode. Clean the surface and connect the electrode and ground connector wires correctly to the new burner cap and place the burner cap back in the opening, positioning the electrode at the same orientation as it was with the old burner cap. Turn the cap one-eighth turn clockwise until the burner is snug. Turn on the burner control to test that the burner functions correctly. Make sure there is no smell of propane or gas when the burner is not in use which might indicate that the burner is not properly fitted snugly.

1. Grab the old burner and twist counter-clockwise. 2. Unplug the wire from the old igniter, simply pull off. 3. Take new burner/igniter (this new one comes all-in-one) and reattach the wire to the igniter underneath. 4. Place the burner so the 'nubs' line up with the stove top and then twist clockwise a short amount, it should turn slightly to lock in place. 5. Test. Mine sparked and started better than it has since i have had the stove

I pulled out the gas range, unplugged the unit from the outlet. Unscrewed about two panels, one is the black cardboard panel located on top, then the aluminum main panel.

Located the spark module, unscrewed the unit from resting plate. Did not change the plate, although the new unit came with a new one, but it doesn't fit. So I just rested the new one on the old plate.

Pulled each wire slowly out and inserted it onto the new spark module.

Screwed in all the panels back and returned the stove to its proper place.

The range now works as well as the oven, but my broiler still does not light up.

Well Got the part within 3 days. Followed instructions to install it and it worked. One thing you need to add to your kit is replacement mounting screws (2 nuts and bolts). It turns out that the original burner because of its age, had a hard time unscrewing it. The screws were very tight and ended up stripped. I ended up using a Dremel  tool to cut the screws off. By now the holes were a little bigger than original so I had to put it back together with a nut and bolt that would fit the small hole. But overall this was my first repair and I would definitely order from you again. Your site's part search and documentation with video clarified it wonderfully. Great service and site!

Barry

Punched out broken screw. Drilled out damaged threads to same size as igniter mounting holes. I used nuts, bolts and lock washers to mount igniter. Would have been very easy if mounting screws had come out. Video very helpful.

The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.

replaced heat sensor

Accessed igniter removed 2screws holding it.unpluged igniter installed new one.

I used a pipe wrench to turn the old burner off and removed the crumbling washer underneath- no need to replace this. I took off the 2 wires, crimped them onto the new burner, twisted it back into place and presto- all fixed!

The repair was a no brainer - twist to release the old burner - disconnect the spark wires. connect the spark wires on the new unit - drop it in and twist to lock - about 2 minute job

First I want thank you for being there for me . If it wasn't for you I would be having thanksgiving at my mother inlaw first iremoved the two screwsthat holds thy element in place. I then pulledthe element out about 3 in and disconnected the two wires . It's easy as 1. 2. 3

slide latches in rear of floor panel forward and remove.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

1. remove oven door 2. remove racks and oven floor 3. remove oven burner 4. unhook igniter 5. install new igniter 6. tuck wiring back in as reinstalling burner 7. put in the insulation supplied in kit 8. install floor and racks. 9. install door. 10. test system 11. oven came on. SUCCESS

I researched the stories on Partsselect, and it looked like this would be a simple repair. Fortunately, it was more simple than I'd thought. We bought the house (and stove) used, and the ignitor apparently had been replaced before, because the part was an EXACT replacement for the old one. I simply unscrewed the two screws holding the old ignitor onto the bracket/burner, pulled the wiring from the back of the oven through the insulation, disconnected the snap connector, reattached the new one. Then I pushed the wiring back through the insulation and added some additional insulation (provided with the part), making sure all extra length was pushed into the insulation. Reattached with two screws using a nut driver, replaced the bottom pan in the oven, slid the door back on its two hinges and started it up. Works perfectly. Thanks Partselect. You guys are great and I had the replacement my mail in about 5 working days!