C206-C Jenn-Air Cooktop - Instructions

Replaced the drip pans

Pulled out the old burner and plugged in the new!

No brain surgery required. Removed electric burner, put in new drip pans. Voila! Good for many more years of service looking like new.

so easy, just ordered the part, the part came and inserted the element into the stovetop

Changed out surface burner switch.Unscrewed two screws, changed plug onto new switch.Don't forget to turn off power!

It was easy enough I unplugged the stove. removed the screws under the control panel,removed the panel, removed the two screws holding the switch in place. moved the electrical wires from the old switch and placed them on the new switch. put it all back together in the reverse order.
it took greater than 15 minutes as this is the first time I did any work on my stove and wanted to be careful and not dismantle too much or scratch anything.

The repairs were very simple we just disconnected one screw then removed the old one and replace with new one. The left side took a little longer, because of the 8 screws we needed to remove to take the back panel off. But once we had it taken off the replacement was a snap. Nothing to it.

Opened the back of the cooktop and found upper right element control switch burned. I removed the retaining screws and wires and spent two weeks chasing the switch at a local dealer. Found exactly what I needed at PartSelect.com and paid less even with shipping than at the local. Installed the switch with original screws and presto!! it worked.

Looked up schematic. Removed 3 screws holding cover. after I shut power off of course. Took off knob. Oriented new control to the one on panel. Disconnected each wire one at at time and immediately attached it to the new control for each wire. Removed screws holding old control and inserted and screwed to the new control and put the knob back on. Put the cover back on. Worked fine. Probably should replace the others as they don't turn as easily as the new one. Probably will spray some contact cleaner which will give me a few more years.

First the power to the cooktop was turned off. Two screws were removed to be able to lift the fan switch holder. The old switch was removed easly because it fell apart. The nuts holding the part in broke as they were removed so they could not be reused. The new switch was put in place however the nuts were too small. I don't know what they were supposed to fit but not these screws. The part was super glued in place. It works perfectly.

The door came off easily after I removed the two hinge covers that are attached to the oven. Taking the door off can be done with one person but ideally two.

The new parts fit in perfectly and the hinge pin used for shipping comes out easiest with a pair or wire cutters (you do not cut it just grab it and pull).

After that, re-assemble the door and drop in place. It was a snap.

FYI...the shipping was ultra fast and the price was great.

No issues whatsover with the entire process.

We unplugged the range from the wall first so as not to get electrocuted. We removed the face of the control panel by removing the screws and 2 hex nuts underneath that hold it in place, and removed the trim. Then we disconnected the malfunctioning control switch, taking note of what order the wires go in. Hooked the new switch up and popped it through the face of the control panel. We then put the trim back, and reattached the control panel with the screws. Very easy!!

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

Disconnect power cord first. I remove the air fan cover to get to the two screws which hold the fan switch and burner knobs. Remove burner knobs and and remove switch cover, disconnect wires to fan switch. Pry spring nuts off with screwdriver to get switch off. Pay attention to which way switch goes on so that it turns on in the right direction. Install spring nuts (they may look too small but they're not) using a deep small socket the size of the spring nuts tap the the socket with a small hammer and the nuts will be locked in place. Put everything back in place and your done.

I unplugged the stove. Took out the burner and removed receptacle by pulling it out of the bracket and clipping the wires. One thing you want to make sure is that when you clip the wires from the receptacle you're replacing you leave enough wire so that you can connect them to the wires on the new receptacle when it is in place on the stove. I had just enough but would have liked more. The bracket I received didn't match the one on the stove so I used the one on the stove since the receptacle itself was the same as the one I was replacing.