All Installation Instructions for Jenn-Air Cooktop C201-C

The heat would not stay on keep heating up and turning off with no low heat

Unfortunately it was the wrong part I replaced the infinite switch and had the same problem so I am still trouble shooting but I plan to continue to use parts select they are excellent to work with and very quick to deliver parts

Parts Used:

Surface Unit Infinite Switch Kit

Nancy from Lakeville, MA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Burner element stopped working

The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

Parts Used:

Surface Burner Receptacle Kit

Robert from Lodi, CA
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Porcelan Electric Burner Plug broke

The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

Parts Used:

Surface Burner Receptacle Kit

John J from Coatesville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

burners would not come on without moving them around

took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

Parts Used:

Surface Burner Receptacle Kit

Ronald E. from Marissa, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Broken switch

Turned off 50 amp breaker. Removed knob, unscrewed holding nut and unplugged each of five wires from broken switch and connected wires to new switch.

Parts Used:

Infinite Switch

Robert from Coral Springs, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

broken surface burner knob

Pulled off the knobs,replaced switch, put on the new knobs. Your web site is easy to use, and your parts are first quality. Dave

Parts Used:

Infinite Switch

Surface Burner Knob Kit

dave from williston, VT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

heating coils would not work

Remove heat coils, take body of coil inserts out, remove screws from body, cut old receptacle out, tie new recptacle wires to the old piece of left over wires using wire nuts, and reassemble body, insert heating coils and test.

Parts Used:

Surface Burner Receptacle Kit

Adam from Kempner, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Thank you for voting!

needed drip pans for burner

easy, drop in

Parts Used:

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Arva from Horsecape, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Switch post broke. Could no longer turn that burner on.

Replacing the switch was quick and easy. It actually took only about two minutes.

Parts Used:

Surface Unit Infinite Switch Kit

Joe from Cottage Grove, OR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

The original filter was decomposing each time I washed it

I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.

Parts Used:

Grease Filter

Sharon from Kenai, AK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

surface burner stopped working. Was not heating up.

The repair only took me 10 minutes to do. I purchased the surface replacement kit from partselect.com. The part arrived in two days. The instructions were very simple. I read the instructions on line during my purchase. When I received the new part, I simply did the repair. Including shipping, the cost was less than $20.00. A service call would have been at least 5x the cost. Thank you for being there Partselect. (Tim from south bend indiana)

Parts Used:

Surface Burner Receptacle Kit