BA1910 Maytag Washer - Instructions

My experience with my repair is as follows:
After determining the "hot water" solenoid was weak and that a new fill valve was needed, I placed my order with PartSelect on Thursday and to my suprise, had it in my hand Friday evening (no special shipping). WOW talk about fast! But unfortunately the part was broken.
Called PartSelect back Saturday morn to explain my problem and was told that I would be credited for the broken part and that a replacement would be sent ASAP probably arriving on Wednesday. Again to my suprise, the part arrived on Tuesday morning.
Hats off to you guys for great service, prices and no hassles.

Dennis Fleming
North Billerica, MA

pulled the front panel first, then lifted the top(2bolts in each).
Then unhooked water and unbolted the water inlet valve from the back left corner behind the tub.four wires are connected Pay attenion to where they go, for easy reinstallation.NOTE: watch the clips in the front of the washer they flew off and it took half an hour on the internet finding out how they went back on.

took hose off then took three 5/16 screws then clamp off reversed order to put back on check for leaks ok

I watched a sample repair on YouTube and read the instructions that came with the part. All went as planned/described.

Removed the front of the washing machine. Located & removed the water inlet valve from it's mounting on the back
inside face of machine. Replaced water valve, & restarted machine. Like new again!

Can't say enough about the speed of parts delivery & professionalism and accuracy recieved from the team at Parts Select. Thanx again,

Greg W.

First let me commend PartSelect for their incredibly fast shipping. Ordered on a Thursday and it arrived on Friday!!

The repair itself was fast and easy and let me add I had never worked on a washing machine before.

1)Unplugged power cord from the wall.
2)Turned off hot and cold water at the shutoff valves.
3)Disconnected water lines leading to the washer.
4)Removed 3 screws holding the bracket assembly on the washer.
5)Removed bracket and pulled water inlet valve out a few inches.
6)Held new inlet valve in same orientation as the old one and then one by one removed the four electrical wires from the old solenoids and attached them to the corresponding place on the new inlet valve.
7)Put inlet valve back in place, attached bracket, and secured it with the 3 screws.
8)Attached water lines to inlet valve and plugged power cord back in.
9)Turned water back on at shutoff valve and checked for leaks.

I washed a load of clothes after the repair and am happy to report that the hot water now runs in as fast as it did when the machine was new. This washer may be 30 years old but I think the old gal's got some life left in her yet.

I ordered the water valve at 12:42 PM one day and received the part at 10:25 AM the next morning. Now this is what I call excelent service. The price of the part was very reasonable. Getting my wife off my back for her washer being broken PRICELESS.

Removed door panel to get to the electric control conponents and noticed a burned wire to one of the door microswitches. Ordered the door switch repair kit from PartSelect. Also, ordered and replaced the thermal fuse at the same time since it was only $12 and didn't know if that blew at the same time the switch cooked. I had the parts coming standard delivery (3-5 days), but they arrived the very next day. Parts included easy to follow directions.Job went pretty smooth and the dishwasher works again Good experience!

Removed old part, installed new part. tested machine. worked fine.

open top of washer
remove two screws that hold water inlet valve
disconnect four wires and hose;replace new water inlet valve and reversed operation
everything went well

Removed the four screws that hold the part and also loosened the screw for a cover. Moved cover to gain access to inside of machine. Removed broken piece and replaced. Tightened screws and replaced plate. No leaks.

The repair was simple, and followed the instructions exactly. Removed three screws, one small hose clamp, and two electrical connectors. Replaced and reassembled. Worked like a champ!

Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.

I found that the water was coming from top of syphon break. Took it out located it on computor , ordered part. Took about 10 min to replace. EASY

The hot water side would fill quickly but the cold water filled very slowly. The seloniods and the valve is built all into one unit. I ordered and replace the part in no time at all. Now both hot and cold water fill quickly.