ASI2175GRS03 Maytag Refrigerator - Instructions

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Take it apart, replace with the new one, put it back together. So simple even a democrat girl could do it.

Disassembled freezer icemaker rear panel and replaced defective part.

Remove the screws and detach the cover. loose the spring and unscrew backwards the plastic nut to release the drum. Un ensemble the blades and release the drum and the deflector replace new parts and ensemble again all the parts.

Replaced the Ice Bin Auger,I ordered from PartSelect,which had much thicker housing and fins than the original .You remove the clip from the end of the shaft and a nylon nut which is a left hand which is opposite threads from most nuts.Its a good idea to take a picture of how the blades and spacers are ,because if not put back in the same direction their will be no crushed ice.It now works better and quiter than when it was new.

Ordered the part from parts selection and when it arrived I unpluged my refrigerator and removed the ice bucket to get to the ice maker. I than looked at what needed to do to remove the icemaker. I removed the icemaker and swapped the parts from the old one and reinstalled the new one. If you don't have any mechanical abilities then have someone that does to help you out.

I followed the instructions on your video.

Repair was straightforward.
Loosen two screws, remove and reuse one screw. Side by side freezer made it a cramped work space.

Replaced drum and reassembled unit.

i used the instructions that came with the part and it was really simple. thank you very much. it saved me a HUGH repair bill.we use alot of crushed ice and the part shipped in 2 days. thank you.C.D.L.

Opening up the Evaporator Fan section was a quick and easy job. After opening, I checked and removed the fan and looked at the grommet. The grommet on the fan was tight and secure and I could no longer hear the noise. I closed the opening. Something I had done while checking the fan grommet must have solved the problem. I have not hear the noise again!

Removed old filter then insert new filter and pushed door closed

replaced the drum ---- however it would of been more helpful if directions came with the part on how to take off the old drum we had to look on line to see how to do that wants we got that done the rest was a piece of cake

Three 1/4” nutdriver screws and a small plug in the rear of the icemaker. Installed in minutes, performed a reset. Working fine.

I removed the back cover that protected the motor and water inlet valve. Removed the screws that held the inlet valve to the refrigerator. Then I took a picture of the wiring and water lines on the inlet valve so I would make sure that I hooked up the new inlet valve properly. When I received the new inlet valve I removed the back cover which I had replaced and installed the new valve. It was a very easy process.