ALZ8580ADW Amana Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken insulator for top burner igniter
I have a Magic Chef gas stove, The top burner came off with ease, just a quarter turn then pull up to expose igniter. Only two wires to remove and two phillips head screws to remove to release igniter. I was done in 5 minutes.
Parts Used:
-
Paul from Block Island, RI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
power boost burner went up and all my burners got very rusty on the underneathe side
We were at a loss for a long time without my boost burner and then while checking all the rest of the burners my husband discovered that all of them had a massive amount of rust on the underneathe side of the burners and that worried me. Well as usual my husband took care of my worries when he discovered Parts Select. We both were pleasantly surprised when we found out that you had what we needed. And the installation was less than 5 minutes, WOW, THAT WAS GREAT! Thanx a million!
Parts Used:
-
Michael from Aberdeen, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Lost on of the Rubber Grommet holding the stove grate
So simple would be embarrassed to give any instructions; it is so self evident.
Parts Used:
-
Martin from Millersburg, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Bottm Of Burner Rusted Out
Took my right hand twisted burner off unplug wires pluged them back into new burner and put burner back on done 3 mins tops.
Parts Used:
-
Paul from Oxford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Igniter not working
Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4
Parts Used:
-
Casey from Soledad, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Flame coming from under burner cap
Unplug power, put strap wrench around burner cap and turn counter clockwise 1/4 turn, remove 2 wires, installed in reverse.took less than 5 minutes.
Parts Used:
-
Tom from Fenton, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
No ignition of gas stove burner
Ordered the part, removed the wires (by light pulling) from the old burner and inserted them in the new one. Tried it, and it worked. Total work time, about 5 min. Amount saved, $150.
Parts Used:
-
Andrew from San Francisco, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The old burner was rotten and leaking
Pulled up the old burner, disconnected the ignition wires, re-connected them to the new burner, replaced the new burner in the stove and presto - everything worked as it should.
Parts Used:
-
Michael from Santa Barbara, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
range top was missing one of the rubber grommets used to hold the grate.
Just pushed the new grommet into the hole. The grommet fit just fine and took about 10 seconds to install.
Parts Used:
-
John from Elizabeth, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The igniter on my stove wouldn't ignite.
Watched a video on replacing igniter. Removed old igniter and replaced it with new igniter.
Parts Used:
-
keith from massillon, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Old burner rusted, flame bypassing
Simply twisted to remove from range top, slipped off igniter wires, attached to new burner, and twisted back into place on range top. Works great,
Parts Used:
-
Pete di from San Diego, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Old burner's flame was coming out below the burner.
1/4 turn counter clockwise to remove the old burner, removed wires. Placed wires on new burner tightened them with pliers,dropped it in, 1/4 turn clockwise--done!
Parts Used:
-
Wayne from Midwest City, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Replacement of top burner igniter
Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3
Parts Used:
-
Godfrey from Las Cruces, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burner rusted flames coming out the side of the burner
turned the old burner to the left and lifted it out. unpluged the wires with a screwdriver pluged the wires into the new burner and putit back on the stove and turned it to the right
Parts Used:
-
Lewis from Tomahawk, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
repair range burner
-
ZHENG from PINOLE, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!