AGS28AWF Speed Queen Dryer - Instructions

I took the front of the dryer off. The two gas valve coils were right in front. Replaced the two terminal gas valve coil and the secondary coil valve three terminal. Cleaned the inside with shop vac and re-installed the front dryer panel.

I took the front dryer panel off by removing 4 screws. I the removed 2 screws from the bracker that secured the 2 valve coils. I unplugged the 2 coils the placed new ones in the exact same position. Fastened the valve coil bracket and replaced the front dryer panel. The dryer worked like new. Thanks!!!

The first thing to do is to check to be sure the vent is clear. The easiest way to see if this is the problem is to pull the dryed away from the vent and let it vent into the room. Once you have determined that the vent is not the issue, take the front cover off and see what is going on on the inside. To remove the front cover first remove the 4 screws on the inside of the upper cabinet to take off the control panel, I was able to gain access to the screws under the front of the control panel that hold the front cover in place. A couple of electrical connectors later the cover is removed. The coils are easily accessed from in front of the burner by removing the 2 screws that hold the small silver cover over the coil. Once the cover is removed, the coils slide off a short shaft and you can replace the coil by swapping the apporpriate electrical connector for the coil being replaced. The coils are alligned with a small white pin so you can't get it wrong. Replace the covers and fire away.

This repair is easy and saves you a lot of money. This is a great web site, easy to identify the parts you need and the delivery is very fast. Nice Job!!!

The diagrams listed online gave me a the information needed to trouble-shoot which part could be broken. It only took two tries to see which part was out but was significantly cheaper than a repairman. The expediant delivery on parts made down-time a minimal. Very pleased with results.

Pretty much just followed the installation video. Took dryer apart and just put everything back the way it was.

Watched video. Made this a very easy repair.Will use this site for next repair.

removed frt cover & drum, replaced solenoids, cleaned the unit interior

My suggestion is to read all of the items that may result in no heat, or insufficient heat, you will find your problem in one of the reply's and the right part to replace. The repair was made much easier, as I installed a Maintenance kit at the same time. Drum rollers, drive belts and tensioner. With the drum out, the coil retaining clip was a LOT easier to re-instal. If the drum isn't out, you can lift the drum up a little and squeeze a stubby screw driver in to loosen the retaining screws. You have to use the proper size screwdriver so you don't strip the screws, and maybe a pair of gas pliers around the handle of the screwdriver to give it a little torque to help loosen the screws, while keeping downward pressure on the screwdriver.

Unplugged the dryer from the wall. Removed the front lower cover. Removed the two screws for the bracket that holds down the coils. Unplugged the coils and swapped them out. Reassembled everything in reverse order. Plugged the dryer back in and started it. It's as good as new.

Found symptoms on Part Select website and confirmed that the problem was the coils. It was extremely easy to find and the site saved me hundreds of dollars on a repairman, labor costs and marked up parts. It literally took about 5 minutes to repair. Awesome site!!Thank You

1)Pulled electrical connectors off each of two gas valve coils. 2)Removed two Phillips screws and removed coil retainer bracket. 3)Lifted off two old coils and replaced with two new coils. 4)Replaced coil retainer bracket and plugged back connector on each coil; total coil replacement time is less than two minutes. 5)Confirmed gas valve opens and gas ignites every time over a two day test period. 6)Re-installed door. Wife Happy. We spent under $20 for 'M' series new style coil kit; and the $7 shipping got it here in two days. What a deal! Terry Rahmer 8.24.2012

Checked heating element and it glowed so I replaced the ceramic gas valve regulators. 4 screws to take front off the dryer and 2 screws to replace part. Couldn't have been easier but I wouldn't have been able to do it without watching the video first.

Remove the two screws holding the door and lift straight up. Remove the two screws on oppostie side. Face can now be removed by pulling straight out at the top, then lifting face up off of tabs at the bottom. The two coils are at the bottom, held in by a retaining bracket. Remove the screws that hold the bracket. Replace the coils by unplugged their wires. That's it!

It was a fairly simple repair to perform with the dryer in place. I simply opened the bottom/front access panel to start, the door removes if you pull up after opening. Then I disconnected the two and three wire connector to the two coils. Next I removed the bracket screws that fasten the coils to the valve assembly. This was a little difficult with the screw closest, because of the small clearance and #1 sized phillips(stubby would work well.) The rear screw I managed to remove by using both a small flathead screwdriver(hex shaped shaft) and an adjustable cresent wrench. At this point, it was a simple matter of installing the new coils and the bracket, and then reconnecting the two plugs. It almost made me want to do laundry.

removed front cover and turned unit on, igniter would glow red but burner would not start. ordered m series new style coil kit and installed. turned unit on and igniter came on and burner started right away. all thanks to parts select trouble shooting guide.