ADE41FSS171TN01 Speed Queen Dryer - Instructions

Checked to see if heating element was warming up by checking through access hole on front of dryer,it was, you know because it glows,so replaced coils and it fixed the problem. Important note, buy the coils as a packet, almost half the price than buying seperately. Thx everybody who sends in info, this is a great site to save people money on fixing appliances

Opened the top, removed the front panel. Supported the drum with my foot while I replaced the coils. I used a very short screwdriver so I would not have to remove the drum.

Unplug appliance from power source. Started by simply using screwdriver or steel putty knife to snap up the top corners of the top section of the dryer. It swings open like the hood of a auto. Looked on the back side of the front panel and found small 5/16" bolts on either side. Removed these bolts and lifted up on the front panel to remove the panel. Slide panel out of the way far enough to access the coil kit on the lower front section of the dryer. (The wires going to the door control switch will allow this without unplugging.) May need a helper to hold the dryer drum up out of the way or prop it up as I did with a block of wood so you can easily unplug/re attach the coil wiring. There are two Phillips head screws that hold the coil keeper in place. Remove these two screws, unplug the two coils (front coil has a three connector plug and the one behind it has a two wore plug). the front coil has a small sleeve that I needed to transfer to the new coil in front. Inserted sleeve as it came out of the old coil, slid both coils back in place, replaced coil retainer being careful to line tabs on top of coils so that they lined up in the coil keeper. Replaced screws in coil keeper. Placed front panel back on being careful not to damage the felt liner that the drum spins on. Replaced the two bolts on the inner side of each corner of the front panel. Lowered the top panel and firmly pushed it back down so that the holders went in place. Plugged it up and it worked perfectly.

Igniter would glow and flame would burn for about 30 seconds then a rattling noise would start and the flame would go out. Replaced the coil and all is well. Very simple and inexpensive. One of the easiest repairs I've ever done. Video was very helpful.

All went very easily

open the back pannel and use multimeter to check the wirings and everything checks ok. open the bottom front panel of the dryer and turn the dryer on. the igniter works and the flame came out for seconds and dies off. the igniter keep coming on, but it seems that the gas was not coming out. i checked the gas line valve and it was open. i had a good idea it wasn't the wiring or the gas line, it must be the coil-valve,(safety coil), that letting the gas flow. i order the parts, it came sooner, which is good, and it took me less than 10 minutes to install, and i only use a philip screw driver. i thank you for sending me the right part in short period of time.

when I see its no gas flame, i deduct the flame sensor and the electric coils not fuction, I order tru partselect and that take me like 30 min. to remplaced those parts.

This repair is very simple. (1) remove the lint screen bracket on top - two phillips head screws. (2) Gently pry open the top of the dryer with a large flat head screwdriver. It hinges backward. (3) Remove the top two nuts on the front panel. Lift the panel upward off the lower brackets. The door wiring is still connected, so I just rotated the front panel to the side. The interior is now exposed. (4) Take the drum belt off the tensioner assembly and pull the drum out. (5) Remove the coil retention plate - two phillips screws. (6) Disconnect the old coils, install new coils. I started the dryer up while disassembled to ensure the new coils worked and the burner fired. But a word of caution ... don't run the burner long with the dryer apart, as it could overheat. After all of this, reverse the process. YouTube also has a couple good videos showing all of this visually. I have very average mechanical skills, and this was an easy job. Another word of caution: most of the metal surfaces inside the dryer have nice sharp edges. Invest in a good pair of gloves to avoid mincing your hands up.

At first I thought the sensor in the drum part was bad. It had some residue from something on it and looked a bit beat up. Replaced it for 30$ and had the same problem. Note: I decided to take the console panel off because I though it was necessary to get to everywhere else and I found a folded up "repairman trouble shooting guide" in the console. Don't know if this is a common place to put it but it had all the wiring and problems detailed with this dryer. It had step-by-step assessment procedures for any problem. However, I punched the sequence for the "brains" to give me a problem code and it indicated that I needed a new "user interface," a 285$ part. I must have punched it wrong because I started to read other problem descriptions and I realized, based on others, that the most likely cause was the coils that regulate the gas/heat valve. I used the "problem guide" to measure the resistance of the coils (it gives you the proper range for each) and one was outside of what it should have been so I purchased a new set of coils for $20 plus shipping. It took me 2 tries at installing the coils because the cover plate that seats the coils in place was not aligned properly the first time. This cause them to vibrate and rattle when starting up. The coils were a little different in height so I readjusted the cover bracket and seated the coils properly. No rattle and the dryer worked perfectly.

unscrewed the 2 screws holding the coil's in place took wires off one coil at a time tested coils with ohm meter found the two wire coil was bad replaced and scered the bracket that holds the coils back in place.PartSelect gave me a list of what was causing the problem and what the % of what was the cause,this helped alot Thankyou PartSelect

I'm a 65-year-old woman with no prior appliance repair experience. I learned on the web that 30% of the time, the failure-to-heat problem is caused by the valve coil, and 30% of the time, it's the cycling thermostat. So I ordered both parts. I watched installation videos on the web. The valve coil was accessable through a front port on the dryer so I started there. I had to go buy a stubby screwdriver because access to the screws was limited. From there, it was easy to take out the old valve coil and install the new one. Just 5 minutes. I plugged in the dryer again, turned it on, and it worked.

The hard part of the repair was the diagnosis. I'd take the front off the dryer, start it up, and the flame would fire up. I'd put it all together, start it, hear the flame start, leave, and it would still be running 4 hours later with the clothes wet. Discovered that one of the gas valve coils would work cool and show connectivity, but would stop working shortly after starting. To check the flame and remove the front, remove the door - 1 phillips screw in each hinge, then jiggle up and down pulling away from the dryer. Then, two screws on the opposite side. Facing the opening, grasp front and pull toward you to swing it down. You can temporarily put the door back with the front off while you start it to watch the flame cycle. On regular heat, the flame will run pretty much continuously - in my case, it would start, run for about 1 minute then stop. I assumed it was cycling, but it really runs longer than that. Coil replacement was easy - unplug the dryer, pry off the electrical connectors, remove the two screws on the left which hold the retainer containing the coils Then pull the coils straight up and replace with new ones. The one with three connectors is in front; the one with two connectors in the back. There are plastic tabs on the coils which fit into holes on the retainer. Reassemble in reverse order. To confirm diagnosis, you can use an ohmmeter to check continuity of the coils. The front coil has continuity between the center connector and each of the side connectors. The back coil has continuity between the two connectors. If you're not getting a reading at 1k ohms, it's probably an open coil and needs replacement.

First, unplug power. The coils are easily accessible from the front of the dryer. Use a 5/16 nutdriver to remove two screws at the bottom of the bottom panel and lift the bottom edge of panel toward you. Pops right out. The assembly with the coils is on the front left. Use a small phillips to remove the coil-retaining bracket. Keep track of orientation of which coil goes where. Slide the suspect coil up off the column and slide the replacement in its place. Carefully slip off wire clips from old to new coil. Repeat for second coil. Reassemble and test.

I first replaced the temperature sensor. That did not help and when doing investigation when thr drier was warm I found the vallve would open and close if I touched the coils

Repair itself was not hard, Pop top, unscrew front panel and pull forward to get at the coils under the drum. --THIS IS THE KEY POINT i ENCOUNTERED: I tested the coils and the resistance was right according to the schematic. But still the flame would go out after while. --on a whim I pulled the front cover and tested the coils immediately after the flam wouldn't re-light.---When the coil got warm, it would open (no continuity). When it cooled down again the correct continuity would return. Replaced the coil and no more problem