ADE41FSS171TN01 Speed Queen Dryer - Instructions

I watched a video. The man speaking was Wayne from parts direct. He made the repair go so smoothly. I enjoyed watching him and I hope you include him in more videos. Had dryer apart and back together (after I had to take top back off, to re-attach the door switch, which I forgot. Had a senior moment!!) in 15 min.And working as good as new. Thank you Wayne. Have a nice day. Bryan

DISCONNECT THE POWER. (I got shocked a few times during the diagnoses stage). Remove the lint catcher. Pop the top of the dryer up (there are two plastic tabs along the front of the dryer. Remove the two screws for the lint catcher and open the top of the dryer. Loosen the screws between the side and front panels. Lift up on the front of the dryer to free it from the clips down below. Swing the front panel out of the way to avoid disconnecting the door-open-switch. Undo the two screws holding the bracket onto the gas burner regulator. Replace the coils. Reassemble in the reverse order. It was helpful to open the dryer door to help align the drum and front panels.

Installed new coil, helped but have other issues that I'm troubleshooting.

replace two heating coils. Dryer working find.

popped top up with flat screw-took out 4 screws (2 screws-1/4" nut driver - 2 phillips screws on bracket that holds coils in place) unplugged 2 wire lugs (1 three wire & 1 two wire) changed out bad coils screws back in-plugged wires back in -popped top back down .done

The front panel was taken out and the parts were replaced. After the replacement, the drying time went back to the original 30-40 minutes.

Gas valve coils need replacing I followed parts select.com video on YouTube and had no problem. It went exactly as the video followed parts select.com video on YouTube and had no problem. It went exactly as the videos showed!

1. Unplugged from wall, turned off gas and opened top cover. 2. Removed two wire clips for door switch and unscrewed front cover (2 screws inside). 3. Removed front cover and moved to side. 4. Unplugged connectors from coils. 5. Unscrewed coil screws. 6. Replaced coils and tightened screws. 7. Replaced front cover, tightened screws and reinstalled wire clips. 8. Closed top cover, turned on gas and plugged in power. 9. Dryer fired right up and made heat.

This 10 year old dryer stopped heating. I knew a Maytag would have much more life left in it than that (even my Mom's lowly GE lasted more than 40 years!) so I was sure it could be fixed. Without doing any testing, I had just guessed that the glow bar was bad and replaced it. But that wasn't the problem - the old glow bar still had continuity as tested with my ohmmeter. So I dug in deeper and looked over the schematic posted on PartSelect's website. The glow bar would light up and then go out, but the gas valve never opened. After probing the two solenoid coils for voltage, I decided the primary solenoid was bad. This was confirmed when I took the connector off and checked with an ohmmeter (never do this with the wires connected!) and found no connection at all between the two terminals.
Ordering the new part from PartSelect was fast and easy and my part arrived in two days. The solenoid coil on this dryer can be removed from the gas valve without taking any gas lines apart - I don't know if they're all like that, but it's a great feature. The only hard thing is that there is no access door to inspect the flame like older gas dryers. You have to take the front panel off to watch it working, but that just involves the four screws around the door opening.
If your pre-Whirlpool Maytag dryer is giving you trouble, take heart! These are great machines that last long, are easy to fix, and parts are easier than ever to get with PartSelect!

and the problem wsa solve

bought the new coil valves changed out new for old, presto dryer works now

First I unpluged the dryer,thenI removed the front of the dryer,spun it out of the way but did not detach the door wires.I then took the two skrews out of the braket that held the old coils,unpluged both coils, I replaced both as I did not have the means to find which one was bad.Besides, I did not want to visit the insides of the dryer for another five years. This was a snap and the parts were perfect and arrived timely.

When you open the door to the dryer there are 4 screws you need to remove (2 on each side) in order to remove the front panel. Once I removed the front panel I then turned the dryer on to see what was happening inside. The heating element was turning orange with a glow but the gas wasn't igniting. After looking on-line I figured my next option would be to replace both gas valve coils (one is 2 terminal & the other is 3 terminal). Once you have the new parts & are ready to install them unplug the dryer. All you need to do is first, unplug the 2 plastic sockets that feed the electricity to the coils (they have wires attached to them) unscrew the bracket that holds the 2 coils in place, pull the old coils out & put the new coils in, replug the electric plugs, re-attach the bracket that holds the coils into place, plug in the dryer & turn it on. Test it without the panel on so that you can see that the gas ignites. My husband was very happy when I told him I repaired the dryer - beats paying another repair man.

I replaced the Thermal Fuse and Cycling Thermostat first, since they were listed as fixing the problem 45% of the time and 19% of the time, but the dryer still didn't heat. I then ordered and replaced the gas valve solenoids, which solved the problem (but I ended up breaking the dryer belt while re-installing the drum, so that had to be replaced too.) In hindsight, I wish I would have ordered all four parts up front and saved a bit on shipping. Installation was easy, especially with the diagrams that showed where each part would be found.

well at first I thought was a sensor so i got it, did not work, second intent fuse end sensor kit, did not work, so I thought must be a valve, so I toke other look up on the price of the valve, then i find a kit to repair that specific problem, so I order it, I got it very quick over night, so I installed in 15 min, and walla!!! did work. Thanks a lot. so if no flame, must be the valves...