ADB1400AWD0 Amana Dishwasher - Instructions

I removed the front of the dishwasher. Then removed the old dispenser assembly, and installed the new one. I don't have as many tools as I need here in our winter residence, so the job took a few more minutes than it would if I'd have had the correct tools.

I had to remove the baskets, spray assemblies (no tools needed) and disassemble the section of the pump that contained the chopper assembly. (removing three Torx screws)
I had to remove a part of the old chopper that had gone into the pump, but I was lucky that a magnet grabbed it so I didn't have to disassemble the pump.
The total repair was not difficult. The only problem was access (hands in the way while repairing difficult to see) and compressing the spring on the new chopper while trying to slip it into the groove.
The parts came in three days and they fit perfectly

Thanks to everyone for posting their experiences on changing the heater element. The most difficult part of the repair was getting the dishwasher out of the cabinet. I didn't know that I should disconnect the water line underneath the sink and this would make the removal easier. Also, because the copper water line going to the dishwasher was kinked, I ended up changing it with a flexible steel braided line.....much easier to install.

Once the dishwasher was out of the cabinet, I turned it over and easily removed the clips that held the heater element in.

I would definetly recommend people doing this repair themselves, it will save you a lot of money!!!!!

The repair went okay. The problem was that the dishwasher would not run after the installation of the dispenser. The door was taken apart 2-3 times. I told my husband (the repair man) that we should pull out the dishwasher so I could clean behind it. I asked him 4 or 5 times to pull out the dishwasrer. Never an answer. Mind you he is an electrician by trade now retired. For some reason while I was not looking he did pull the unit out after 2 hours of fussing with this electrical problem. Remember he is an electrican by trade. When he pulled the unit out "THE PLUG WAS OUT OF THE SOCKET". How funny!!!!!!!!!!!!!!!!!!!!!!!!!!
I could not stop laughing. I had to answer the phone at that time and my friend thought I was out of breath from running for the phone. I told her later it was from the PLUG OUT OF SOCKET TRICK. I still am laughing. The first thing an repair mann will ask you is if the unit is pluged in. I have two sons and one son-in-law that are electricans and will have many years of fun telling this story. It is good to laugh. I will be laughing for a long time.

Followed directions from YouTube video.

Repair man said I needed a new pump and would cost $350 to repair. This dishwasher was only 5 years old and we only use about once a week so didn't think the pump was gone. Went on this website and read some stories. this model has a mini garbage disposal with a chopper and screen which gets clogged up and prevents water from circulating. You can clean the screen without removing the dishwasher. Remove the cover plates on the bottom with 4 screws and the smaller cover plate underneath. Remove screen, clean and replace. If the chopper is broken you can order a replacement for $21. There is another story on this site with a lot more detail so I wont repeat here.

I closed the water at the tank and opened all the hot water faucets in the house thereby draining static water from the inlet hose at the valve. Then I unscrewed the inlet hose from the valve, unscrewed the valve body from the support bracket under the tub, unplugged the electrical plug from the valve body, and removed the outlet hose. I installed the new valve using the reverse sequence. Then I closed all the hot water faucets, turned on the hot water at the tank, and purged air from each of the faucets. I then started the dishwasher and ran it through a complete cycle, periodically checking it for leaks, and found none. Total time for uninstall and reinstall - about 30 minutes. Not bad for an 80 year old.

The repair was straightforward. The hardest parts were pulling the dishwasher out from the counter and keeping the dishwasher from falling forward when I needed to reach inside. The instructions in the video were accurate. I was very glad I bought the rubber washers, because I could not reuse the washers from the original heating element. Easy enough repair to do on your own.

Used bowls in upright position in upper shelf determining no water to upper shelf after running in rinse cycle. Added a cup of Vinegar in rinse cycle. Performed bowl test in upper rack & still no water in bowls. Dismantled inside of unit by removing both spray arms & found lower seal deteriorated & upper seal in need of replacing. Replaced seals & redid bowl test & found no water getting to top rack still. Found utube vid showing removing garbage disposal portion of unit. Requires removing screen in bottom of dishwasher. One screw attaches garbage disposal cover. Found non food items & food by broken garbage disposal. Repaired disposal, removed debri & reinstalled all components. Redid bowl test in upper shelf & bowls were overflowing!!????Dishwasher works GREAT now & can hear garbage disposal operating along with massive water being sprayed!!!

Take out 6 screws from inside door upper most screws to control panel, removed water safety shield 3 easy tabs to release, found old fuse removed , cut wire 1 inch from old fuse removed have to pull fuse out of its plastic holder put in new fuse matched up wires, they are color coordinated, black with white stripe, and one solid black striped wires and twisted them tight, and inserted them in new wire harness that came from parts select tighten them tide them all together and used black electrical tape on all the new connections put back together and it totally fixed the problem so happy saved alot of money not having to call a service repairman

Pulled washer out far enough to put 2x4’s under front feet. Removed front panel, I clipped wire connector and unplugged it. Pushed plastic locking lever in and twisted unit counterclockwise. Wiped inner rim and reversed above procedure to assemble.

Pull dishwasher out a few inches. Disconnect spring from plastic connector with long nose pliers. Remove connector. Replace friction sleeve. Replace connector.Reconnect spring to plastic connector. This completes repair.

Ordered a new pump (after a online diagnosis). Followed the instruction video on the website...also took the time to replace the discharge hose due to residue buildup...tested dishwasher (one cycle). Slide dishwasher back into opening....DONE. Works perfectly. THANKS

removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.

Repair was easy. Step by step instructions on touTube