A9495VRV Admiral Microwave Oven Combo - Instructions

The ignitor heated up and the broiler worked but not the bake mode. Repaired per instructions

I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range, there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.

it was so easy my wife could do it!!!!!!!!

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.

I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.

Remove rear sheet metal cover. Disconnect the temp sensor wiring connector (on the left side as viewed from front).

Open oven, take out the 2 screws attaching sensor and remove. Reverse for installation.

Included wiring adapters are not needed for this model oven.

1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.

Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Remove two screws back panel and remove sensor two screws inside top oven.

Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.

Screwed in light bulb and glass protector

Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.

very easy

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.