A702S Maytag Washer - Instructions

Remove 2 screws from bottom of front panel, swing panel out and lift off. Remove 2 hex head screws from inside front corners. Lift top to expose injector in left rear corner. Remove clamp, remove injector from air break box then use screwdriver to pry the lip back through the hole in the tub. Carefully squeeze the lip of injector through the tub hole. Silicone grease or liquid detergent may help. Then reattach the injector to air break box and reassemble washer.

Found the parts I needed on your website along with a video that showed exactly how to do the repair. Set my iPad on the dryer and followed along step by step. Never would have tried something like this without your helpful information.

Removed wet close and removed 99% of all the water with a simple sifon hose and sponges. Diconnected electric and water supply hoses. Layed washer on its back. Removed front of washer. Disconnected hoses to water pump and checked for blockage. None. You need to capture the risidual water from the hoses and the pump if you are working in an area that cannot tolerate spills. Pulled pump out (three screws) put a screwdriver and blocked the pump impellar and rotate the punps pully. Pully rotaded freely so the pump is bad. The two belts were pretty worn out so I replaced them also. Hooked up everything in reverse. Adjusted the tension of the belts as required. The drive belt for the pump should be pinched to 1/4". Checked the moter glides also. Put everything back together, checked for leaks and did a load of wash. Everything good. Dismanteling and diagnostics and clean up took about 30'. Assembly took another 30'. Purts fit perfectly.

Received wrong springs for my model had too use combo old spring with the two new (too long) springs to get the tension on the belts. For now it working. Did not contact you due shipping took so long and two delay date change by FedEx ground. I didn't want to go thru another delivery nightmare. Thanks for the time.

Tilt the washer sideways. Remove belts,Remove front panel, loosen two hoses, loosen three small nuts. Take out old pump and install new new pump vise versa. Video provided by partselect very helpful.

Used duct tape as the video provided instructed and also to hold second hinge lid ball in place. Firmly pushed down on the lid until it easily popped in place.

Unhooked water and drain lines, Unplugged electrical. Removed the two phillips screws at the bottom of the front cover. Removed the Front cover. TIpped machine backwards at about a 45 degree angle using a 2x4 to support the machine. Removed the pump belt and the drive belt. Installed the old pump belt and the new drive belt. Loosened the 3 each 5/16" bolts holding the pump mechanism and moved pump to the left. Moved pump to right to tighten pump belt and tightened the left pump bolt. Loosend the one pump bolt and pulled the motor to the left to tighten the drive belt and holding in this position I tightened the pump screws, Pump belt was now looser than the drive belt. Ran washer and it worked perfectly.

Received drain pump by fed ex, put it on in 15 minutes. . . My wife was very happy again. . . .

I first removed the front panel of the washer and removed 2 screws holding the top of washer in place. I had to flip the top up. This allowed easy access to the tub. I then removed the agitator by removing the set screw on the lower portion. From there I loosened the mounting securing device by using the nail punch and hammer inside of the tub (it was loosened by turning it clockwise). The tub was now loose and I removed it from the washer. Next I removed the torx set screw and the tapered hub unit (cork on it). It had to be again loosened with the hammer and nail punch and turning it clockwise. This exposed the part that needed to be replaced. I replaced the old with the new and the washer now works great with no leaks! Be sure to clean everything you remove that will be reassembled.

Observed source of leak by lying on floor behind washing machine and placing hand in likely spots. Found water injector hose was source. Searched web for instructions to open up washing machine: 2 screws at bottom of front panel, then 2 screws at top inside after removing front panel. Easy after that. Lots of rust and rusty screws and rusty tinnerman nuts; had to grind off one of the screws with dremel tool.

First I removed the two screws to pull off the front panel. I then removed the two screws (1/4 inch head) in the upper front corners. Removed clamp from siphon break and carefully worked off hose. After a couple of failed efforts to put hose on dry I put some o-ring type grease on the barb and it went on easier. The clamp was a bit difficult too but take your time and it will go on. Putting injector end in tub required patients. Reassembly was reverse of above. All good for another 25 years!

Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wall box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.

I viewed and followed the PartSelect Instruction Video. My only problem was reattaching the door after the hinges fell off.Everything fell into place as the video indicated. After I regrouped I was able to put the hinges back and then I was able to reattach the side panel very easily as the vedio indicated. Thanks for everything.

My 13yr old son and I fixed the washer in about 5 minutes. It was very simple and easy to repair considering I had never done it before.

I was only missing one of the bumpers but that was in pretty poor shape so I replaced them both. It didn't take much to do. Just pressed the bumper into place and Viola! instant gratification.