A3520SPA Admiral Range - Instructions

Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering processes were simple and delivery was faster than I hed expected.
Thank you

Turned off power circuit to oven. Removed old element by unscrewing two nuts attaching unit to back of oven. Used pliers to help release electrical connections at both ends of element. Re-attached connections to new unit. Screwed nuts back into place. Turned power back on and cooked dinner. Total time for repair was less than 5 minutes.

This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.

Piece of cake. Removed the Phillips screw with screwdriver, placed new one on the slide and used old screw to screw it in place. Drawer does not lean to one side anymore.

First I removed the two screws that hold the element in place. I then pulled the element out about three inches and disconnected the two wires, being careful not to pull the plugs off. I then inserted the new element and reattached holders. It was very easy and took less than five minutes. The part arrived amazingly quickly. The stove works great now.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

Rehooked up wires on new element, Slid the element in place. Replaced the two screws. Done, very easy.

My husband removed the screws holding the damaged element and removed it before the new one arrived. When we received the replacement part, it took only about 10 minutes for him to repair the oven, inserting the new element.

My wife detected the problem Wednesday evening before Thanksgiving. We've had the heating element break before, so we knew right away what the problem was. We ordered the part that night, and even though we weren't able to cook Tom for Thanksgiving, the part shipped on Friday and arrived the next Thursday.

First, I turned off the power to the stove at the circuit breaker.

Then, I removed the two screws that hold the element in place. They are on the top of the flange and partially concealed by the convection element that juts out.

I pulled out the heating element, disconnected the electrical leads, and installed the new one.

I attempted to put the screws back in, but they were a little tough to line up. I decided to leave them out, knowing that I will probably be doing this repair again in a couple of years.

Hopefully, next time it won't be the day before Thanksgiving.

I removed the heating element and noticed that the prongs were corroded. I looked for a model number but couldn't find it so it made it difficult to find a replacement until I got on this website. I found the replacement part and also found that as I checked for other sites for this part this company was the most resonable priced.
The part arrived and I replaced it in seconds. Turned it on and it worked immediately. Super easy.

remove elements and replace bowles

I removed the old and repaced with new. I never ordered anything one day and got it the next. I'm impressed

i read the installation instructions and followed them. first i made sure that each heating element was off. next i carefully removed each one (a total of 4) from it's plug and lifted the worn out drip-bowl up and replaced it with the new one. finally i pluged in (a total of 4) heating elements and turned them on to make sure them were working and they did.

Package arrived while I was working at the computer and my husband announced minutes later, "That's what I like to see". I didn't know what he was talking about until he tossed the packing list on my desk and said, "It works perfectly. Good Job!" It had only taken a minute to pop the new parts in and he already had water on for coffee.

1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements

first I removed the 2 screws, I then pulled the element out., accidently lost one of the wire in the insulation and had to take the back panel off which was 8 screws. Probably doubled my time. I received my part in 4 days thanks to good service and FedX It arrived the day before Thanksgiving. Just in time, Thank You All.