91FA-3KX Magic Chef Wall Oven - Instructions

Remove the the drawer of the gas range on the bottom, on the right side there is a alluminum cover with a bunch wires, held on with two screws,inside is the igniter kit module, make sure you unplug the range from the wall . unplug the wires from the unit and plug the new unit up and you are finish.Good luck.

First, I removed the racks, door, bottom drawer, and lifted the bottom pan up and out from the rear. Then, I unscrewed the bottom cover for the electrical stuff (under where the drawer is) as this is where the connector for the igniter is. I did a voltage test on the oven side of the connector, finding voltage there I removed the igniter by removing the 2 screws holding it to the burner. (pack lunch for that part, they will be rusted, I used a mini grinder to cut off the heads). Then I pulled the connector through the hole, and installed new igniter using self drilling screws. After i repacked the insulation, I put it back together, and it lit right up. The failed one had a bad ballast, confirmed by a continuity test.

I was worried over the fact that my oven was filling up with propane but taking a long time to light. One day it didn't light for over ten minutes. I shut it off and put the still frozen pizza back in the freezer. That's it, I thought. I'm not going to use the oven again until it's fixed.

I looked online and ordered the part. It came within two days time,even though it was a weekend during the holiday season. My husband spent about 15 minutes with his head in the oven and then said it was fixed.

I baked several batches of Christmas cookies and three coffee cakes the next day.

This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out. First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is held on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle. Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I would like to now say something about the excellent service received from parts select. They have an excellent user friendly site & I received my part the next day.

unplugged the oven, unplugged the ignitor and removed the two screws

My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.

Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.

Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.

Replaced the oven ignitor. Toughest part was removing old screws.

I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for years because I didn't realize how easy the fix was.

Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.

Unpluged then stove, turned of the gas.Unpluged the igniter from the harness, unscrewed the igniter and pulled it out through the front of the stove.Installed in reversed order.Stove works like new. The part got to Alaska in 2 days. Thank you for your service.

very easy

Screwed in light bulb and glass protector

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes