7WSC19D2XS01 Whirlpool Refrigerator - Instructions

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

I had watched several video's on installing the plugs in the Kitchenaid model that I had, but when it came down to the install the figuration was a little different. I did figure it out and the rest was a piece of cake. Remember to shut the power off!

Replaced the Ice Bin Auger,I ordered from PartSelect,which had much thicker housing and fins than the original .You remove the clip from the end of the shaft and a nylon nut which is a left hand which is opposite threads from most nuts.Its a good idea to take a picture of how the blades and spacers are ,because if not put back in the same direction their will be no crushed ice.It now works better and quiter than when it was new.

Take it apart, replace with the new one, put it back together. So simple even a democrat girl could do it.

Remove the screws and detach the cover. loose the spring and unscrew backwards the plastic nut to release the drum. Un ensemble the blades and release the drum and the deflector replace new parts and ensemble again all the parts.

I took off the broken tube and attempted to order a new one with the confusing we sight at parts.com- after 3 attempts I finally got the right part with help from the operator at parts . Com( nice and helpful) but had to ship wrong parts ( the 2 wrong ones) back. The parts were of good quality and we're not hard to put on

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

removed freezer shelves, removed back panel with screw driver. removed wires from fan motor, removed fan motor from mounting bracket, removed fan from motor. installed new motor in mounting bracket, installed fan on new motor,installed wiring on new motor. turned power on to check operation, installed rear panel and shelves. total time for job about a half hour

i used the instructions that came with the part and it was really simple. thank you very much. it saved me a HUGH repair bill.we use alot of crushed ice and the part shipped in 2 days. thank you.C.D.L.

I followed the instructions on your video.

Unplug fridge, remove shelves, remove back cover, unplug old motor, remove adapters from old motor, put adapters on new motor, install new motor, replace cover, replace shelves, plug fridge back in, give it 24 hours to stabilize thermally.